Copter goes wild in stabilize or Auto mode
@Pilot2016 wrote: Hi, this is my first time here. I am using APM mini 3.1. Copter goes wild always if I switch flying mode from default manual to either stabilize or Auto mode. First time when...
View ArticleNeed compiled v2.50
@jborden wrote: Does anyone know of a site with a compiled version 2.50 or maybe have it archived?I need to revert back to it from v2.51 beta and am clueless on how to compile it from the zip...
View ArticleAdding Channels for Air Data Vanes to Firmware
@Donald_Lear wrote: I've got a Pixhawk Autopilot system and I'm trying to get it to receive voltage data from a pair of potentiometers. I have little experience with the firmware, and I don't know...
View ArticleMavproxy.py location?
@rsjsrc wrote: I have MAVProxy on my RPi3 and I used the find command to learn the following pi@raspberrypi:~ $ sudo find / -iname...
View ArticleHigh Speed Auto
@wicked1 wrote: I've been trying to get my little racer copter to do auto missions as quickly as possible.. But am failing. To start, lets talk about "speed up".In stab or acro, the copter goes up...
View ArticleAirspeed sensor unhealthy
@timvand wrote: I have two of the 3DR Aero's, which on boot are showing "Airspeed sensor unhealthy" in the message. Screenshothttp://prntscr.com/c42kkr Is it likely that both would be bad? The pitot...
View ArticleGeotagging v1.3.39.1
@timvand wrote: The file size is almost double when using v1.3.39.1 vs 1.3.39. Why does that occur? Thanks! Posts: 8 Participants: 2 Read full topic
View ArticleFlight Mode 6 stuck at manual
@timvand wrote: On MP and using ArduPlane, Flight Mode 6 is grayed out and defaults to Manual. Screenshothttp://prntscr.com/c42phw The value change be changed in the Config Tab and changing the value...
View ArticleArdupilot Sparkfun Xbee adaptor problem
@Wally wrote: I was trying without success to use the Sparkfun adaptor with an XBee to get wireless operation for my Rover. After getting the elusive schematic for the APM2.5 and the schematic for the...
View ArticleUnexpected RTL during Auto Mission
@dkemxr wrote: 3.4Rc2 has for the most part been working well. But today I had an unexpected RTL during an Auto Mission. Both GCS and Throttle fail safe are set for "continue with mission" and battery...
View ArticleImpossible to calibrate Compasses AC 3.4-rc2 with MP 1.3.39
@lorbass wrote: The compasses (internal or/and external) where not to calibrate with MP 1.3.39Whether via the 3DR Radio nor via the USB. Error message: There is an unexpected error But with QGC no...
View ArticlePixhawk read analog source ADC 6.6V
@pedro_carrola wrote: Hello to all members,I am currently working on ArduPlane 3.6.0 code in order to read an analog voltage across Pixhawk's virtual pin 15 (in ADC 6.6 Volt port). To do this, i...
View ArticleAutotune never ends (rc1 and rc2)
@lorbass wrote: Never ending autotune As with -rc1 also -rc2 never ends the autotuning within 7 min and for Roll only.The values decrease slowly from the manual setup below the defaults.With the...
View ArticleClik here to view.
AC3.4rc2, FS_BATT_ENABLE
@tommal wrote: Did the first Testflight today with rc2, MOT_THST_HOVER is working as far as i can tell. Did set the default to 0.3 and it adjusted it down to 0.2427... during alt hold. Are we...
View ArticleCopter became hardly controllable and crashed; Log indicates a fail to enter...
@Daniel_Frenzel wrote: I tested my Copter (Navio+ board from Emlid and RPi2). The copter was started in Stabilize and later I switched to AltHold. From there the copter behaved weird. It was hardly...
View ArticleSpline Waypoints
@ChrisOlson wrote: Just a quick question for someone who may be able to shed some light. If I prepare a mission with APM Planner2 using spline waypoints, upload the mission to my quadcopter, go to the...
View ArticlePower consumption and optimization with ArduPlane
@paan2097 wrote: So far I have studied all the plane parameters relevant to power consumption. Major ones that I assume affect power consumption are throttle, roll, and pitch limits and their...
View ArticleAre there any gimbals? Compatibility?
@PSYCHICS123 wrote: Can anyone recommend me any pixhawk gimbals for my f450 quad?? Posts: 2 Participants: 1 Read full topic
View ArticleFirst flight and autotune - impressions and small issues
@tabascoz wrote: Hello, Yesterday i did my first flight with 3.4rc2. I took the opportunity also do run a full autotune session again and the values found seems more reasonable than with rc1:...
View ArticleAPM Plane 3.6.1 release date? Zubax GPS Fix
@Jcooper21 wrote: Is there any update on the release date for APM plane 3.6.1 with the zubax GPS fix? Posts: 1 Participants: 1 Read full topic
View Article