No GPS issue on MP
@mutyo051026 wrote: Hello. I'm using uBlox Crius Neo 6 with KHPilot32. I confirmed that the GPS itself is working properly using u-center, but when I connect it with the Pixhawk, MP says No GPS (No...
View ArticleNo module named dronekit
@Lefteris wrote: Dear friendsI'm trying to install SITL on Windows 7. The process is getting according to the instructions...
View ArticleMission Planner simulation problems
@Lefteris wrote: Dear friendsI'm trying to install SITL on Windows 7. The process is getting according to the instructions...
View ArticleNo PWM outputs Ch8-Ch16. Advise please
@Fettler wrote: Hi.Im trying to add a seagull camera controller to my pixhawk setup. When I monitor RCin in on the various channels I want to use (like AUX1, RC9) there is the correct PWM signal but...
View ArticleAltHold mode running KDE
@copilot wrote: Hi I am busy building a new X8 using KDE motors and their UAS55HVC ESCs. These ESCs does not normally require calibration but when using them with the Pixhawk it is recommended to buy...
View ArticleClik here to view.
APM V3.1 Channel in and Channel out
@tomerinbar1 wrote: Hello All, I've a problem that I can't find any solution for it. After I arm the board and rise the throttle it's jump to pwm 2028 on the ch1,2,3,4out. It's just jump straight away...
View ArticleTerrain data - When is it deleted off the Pixhawk?
@Pedals2Paddles wrote: From reading the guides on Terrain data, I completely understand how it decided what terrain data to request from the ground station. And I get that it stores it on the Pixhawk...
View ArticleOptical flow behaving badly indoors (possible rangefinder issue?)
@ollenorelius wrote: I'm trying to fly a quadcopter autonomusly indoors using a optical flow sensor, but I'm getting quite erratic results trying to fly in Loiter. I've followed the guide from the...
View Article433 telemetry radio + micro minimosd
@turborocket wrote: hello to all, im trying to setup my apm 2.6 with a radio telemetry module and micro minimosd with mwosd firmware. they are perfectly working, but if i connect both together with a...
View ArticleClik here to view.
HELP: Battery Failsafe Crash
@crazy1pilot wrote: Hi All, I recently encountered a problem that has me a little puzzled and I am hoping someone can help me figure out the cause. a few days ago I was adding the finishing touches on...
View ArticlePX4Flow position estimation
@Nafnaf wrote: Hi, is there a log parameter to view the position/path of the drone, which is estimated by integrating the optical flow velocities? Thanks! Posts: 1 Participants: 1 Read full topic
View ArticleServo size for tilt rotor?
@ultrafuge wrote: Hi, what kind of servo (normal or retract) and what size is suggested to tilt a Tmotor MN4006 with an 15" prop ? Posts: 1 Participants: 1 Read full topic
View ArticleArduplane 3.7.1 issue with lidar in serial and I2C port
@kalai1219 wrote: Light ware range finder doesn't connect with serial as well as I2C port . It's shows bad lidar health. What could be the problem. Posts: 1 Participants: 1 Read full topic
View ArticleMotor order in motor balance warning
@Anthony_Short wrote: What is the motor order in the log Auto Analysis report from MP? Is it this: http://ardupilot.org/copter/docs/connect-escs-and-motors.html? Or the ABCD ordering used in the motor...
View ArticlePX4 I2C Airspeed Sensor
@artemen wrote: Hi, if someone can suggest anything:PX4v1 I have 3 devices on my I2C bus: external compass, LED and Airspeed Sensor. all devices work correctly when powered from USB and AS shows...
View ArticlePixhawk 2.1 & Here+ Crash; Possible mech failure?
@jprouty wrote: I received a Pixhawk 2.1 on Nov 23rd (a lucky early bird). Everything was going fine, until a week ago! I followed the service bulletin when it came out. I had a Here+ unit on it at...
View ArticleTransport Canada Special Flight Operations Certificate Questions
@lydia wrote: I'm in the midst of applying for an Special Flight Operations Certificate from Transport Canada and am a bit confused by some of the documentation I've encountered with the Mission...
View ArticleMission Planner - Suppress Error Announcements
@Marc_Dornan wrote: I assume this is for Michael. Just a thought. I was setting up a new Pixracer through MP the other day and it did just occur to me that it can be maddening to listen to all the...
View ArticleLoss of control and warnings after power cycling
@jamescooper1 wrote: Trying to figure out what may have caused a series of faults ending up contributing to a crash. Background: We have been testing a sense and avoid system utilizing the TX board...
View ArticleClik here to view.
When autotune becomes a testcrash
@Carpenter wrote: Hi, I'm a fan of ArduCopter for a number of months now, I've trying to build a copter dedicated to photogrammetry on an Alien GF680 frame.Step by steps reading the wiki and the forum...
View Article