Drone sudden crash log
Hello, everyone. Can anyone help me regarding my current logs? My drone was able to takeoff and hover then it suddenly crashed. Just needed to confirm if its motor/esc/prop failure. And in which part...
View ArticleWhy is RTSP Video Lagging in QGroundControl Daily (Master), but Works Fine in...
Hi everyone, I’m facing an issue with RTSP video lag in the QGroundControl Daily (master) version. I’m using the following setup: 1.Cube Orange+ 2.SIYI MK15E remote controller 3.SIYI A8 Mini camera...
View ArticleClik here to view.
How to Test the Time Synchronization between Radar and Camera?
In multi-sensor fusion systems, coordinated perception between cameras and radar has become critical for environmental understanding. Cameras identify object categories by capturing texture...
View ArticleSetting up motors - takeoff issue
I am porting a betaflight DARWINF411 fpv to use H743 Flight contorller. flashed copter 4.7.0. I have done all the steps to prepare the drone for flying moving the motor wires to the same pad names...
View ArticleOnly GPS/RSSI/BtRx sensors found on my FrSky Rxsr/TaranisX9D telemetry feedback
Hi. I’m getting troubles setting up a decent telemetry feedback from my KakuteH7 AP, through an FrSky RXSR radio receiver connected (and firmware upgraded to F.Port protocol). Then only sensors...
View ArticleUnresponsiveness of servo motor with radiolink crossflight
I recently bought a crossflight flight controller and used it in my ardupilot Quadcopter. Drone is working well , all flight modes are perfect but I am not able to figure out why my servo motor isn’t...
View ArticleInstal and software help on Arducopter
Its been around 2-3 years since I attempted installs to this Raspberry Pi 10" bladed drone due to heart surgeries. Back then I never got this thing off the ground and I’m wondering if there are any...
View ArticlePort ardupilot to custom STM32F405 board
Hello there! i want to develop custom PCB with STM32(which ardupilot support), i’m looking for some basic PCB design refereces and how to port firmware on custom board 2 posts - 2 participants Read...
View ArticleCubeOrange+ Barometer Error ($CHECK_BARO1_PRESENT)
Hello, I am using CubePilot CubeOrange+ and I have installed ArduSub 4.5.0 firmware version on it. However, I constantly get $CHECK_BARO1_PRESENT Failed error. I think the internal barometer inside...
View ArticleClik here to view.
Hydrofoil Arduplane setup sonar sensor
Hello everyone! I am currently trying to setup an electrical hydrofoil craft built from 3D-printed plastic. I am using Pixhawk Cuav V5+ and latest update of arduplane. All servos seem to work well to...
View ArticleClik here to view.
Oscillations in estimated measurements
Hi, I would like to get an opinion about what im seeing with my data. I can see small fluctuations in AHR2 estimated attitudes and EKF. Despite the vibrations show way below what is recommended and no...
View ArticleClik here to view.
AM32 firmware updating issue over passthrough
Hi I tried to reflash a new T-Motor F55A III with the latest firmware. I noticed that the connection over the CUAV Nora (Arducopter 4.6 beta 5) is often very unreliable. Mostly I have to connect...
View ArticleClik here to view.
About not pre arming
Gps alt 5819m see baro this error show in pree arm solve my problem 2 posts - 2 participants Read full topic
View ArticleHelp on log analisys, Helicopter crashed
Hi all, I have a bit or rust on log analisys for helicopter. Yesterday I was going to do a routine test flight to check new battery and heli crashed just after take off due to lack of control. it was...
View ArticleClik here to view.
Pitch response when changing throttle quickly
Hi, apex 7" , 4.5.7, am32 When the throttle is sharply increased, the nose rises, when the throttle is released, it drops in the stab and acro modes. Which way should I look? If I raise pitch PID, the...
View ArticleClik here to view.
Setting MOT_THST_HOV from logs
Hi! I am new to the Drone Building Community. So recently made my first drone ever. Gave it a test flight. Here are a few things that I observed: First flight, done in Stablize mode. Observed wobbles...
View ArticleClik here to view.
Videolink & Parameter communication problem QGC android app to 3DR Solo with...
Hi, I sometimes have problems getting video and always have problems controlling GoPro on 3DR Solo with OpenSolo 4 and AC 4_5_3 . Can someone help? I also get Error during 3DR Solo Video link setup: 5...
View ArticleDrone build pdb board
Tarot High Current Heavy lift 12S 480A PDB & 6X Signal Hub - TL2996 - Flying Tech i have this is there an easier way to connect my flight controller signal not power to them black connectors on...
View ArticleQuad X Motor Tailsitter without control surfaces
I set the mode to “manual” and increased the throttle on the ground. The motor speed increased. The yaw speed change was correct, but there was no speed change in the motor during pitch and roll....
View ArticleClik here to view.
Strange Compass Orientation
Hi all, I know this is a strange way to mount the compass (the unit behind/to the right of the battery in the photo - Walksnail GPS/Compass), but I’m trying it for now until I potentially move it to...
View Article
