Showing throttle in values
@moreba wrote: I need see throttle percent in values widget ( ch3percent in missionplanner ) . Posts: 1 Participants: 1 Read full topic
View ArticleHere+ RTK GPS serious hardware problems
@Javier_Beringola wrote: Hi everyone, after connecting the drone wait for all sensors to work fine, connecting through NTRIP reaching RTK fix after 3D fix and float, and upload the survey mission to...
View ArticlePing ADS-B receiver data on flight screen
@Verloop wrote: @Michael_Oborne Could it be possible to show the most relevant data of airplanes detected by the receiver like altitude, heading and speed together with the plane on the flight data...
View ArticleClik here to view.
ArduPilot Featured in DIYODE Magazine
@CraigElder wrote: diyodemag.com Take Flight With H4WK Building your own drone might seem like the exclusive domain of hardcore flight enthusiasts. But you can do it too - we show you how! Posts: 1...
View ArticleNo servo output
@Ahmed_Khan wrote: Hi. I am new to arducopter. I have a set of 4 racerstar and another set of 4 simonk 30a escs. I am able to calibrate the escs (all at once) successfully (using any set at a time). I...
View ArticleLooking to purchase pixhawk 2's with edison ready carrier boards
@Jose_Ortiz wrote: As some of you may know the intel edison was discontinued a while back. Therefore the edison ready carrier board was also discontinued. Im looking to see if anyone out there has any...
View ArticleBest low cost avoidance sensor?
@vosair wrote: Hey all! I’m looking for a reliable and inexpensive rangefinder. It seems like benewake is a popular brand. What would you recommend for use with the cube? Ideally something on I2C to...
View ArticleClik here to view.
How to use a real serial device in SITL?
@goredhawk wrote: Hello everyone, i am try to use a real serial 3dr telemetry in SITL, it’s baud rate has been set to 115200. i followed the link:...
View ArticleClik here to view.
These guys are using ArduCopter to build an Holonomic Hexacopter (OmniCopter)
@lordneeko wrote: reddit r/Multicopter - Me and my coworker developed an "omni-copter", it moves sideways... 71 votes and 18 comments so far on Reddit They still have a few bugs to work out. The goal...
View ArticleClik here to view.
Log Crash Analysis Help
@blahdc wrote: Hi All, I have been flying a 3DR Solo and on my last flight I sent a mission to the drone and looked back up and it dropped out of the sky. This was only a few minutes into the flight...
View ArticleClik here to view.
Uncontrolled position Problem in Auto mode and Cut motors in Qland
@moreba wrote: Hi, I had problem in Auto mode . Vtol plane in auto mode does not control alt and position . also when i changed mode to Qland autopilot cut motors and does not control land speed ....
View ArticleDimensions of Pixhawk 2.1 carrier board
@dinnertimebandit wrote: Hey all. I’m away from my pixhawk so I can’t check this myself. Does anyone know the dimensions of the carrier board? I can’t find it anywhere online. Thanks! Mike Posts: 1...
View ArticleNimbus 1800 purchase locations
@Chad_Frazer wrote: So last night I get an email from banggood saying that, “We regret to inform you that your order was returned due to the failure of security check when passing the customs office.”...
View ArticleQuestion about stereo obstacle avoidance
@Iron_Donkey wrote: Hi guys, I just wanted to ask (and sorry if there is a better area to place this, please let me know if so and I will move it to the correct category) I saw that PX4 now supports...
View ArticleClik here to view.
Octocopter Tunning
@ardisd wrote: Enclosed is a log for a 4.7kg octocopter in X configuration. With a 10-15mph wind I notice the copter bounces around a bit but. On the log comparing Desired again actual Pitch the 2...
View ArticleClik here to view.
CANbus for Ardupilot with UAVCAN and UC4H
@mike wrote: CANbus for Ardupilot with UAVCAN and UC4H I think that CANbus is the single most important feature added to the Ardupilot eco-system for years. What is CANbus? Think of CANbus as the...
View ArticleCamera control depending on MODE
@charles_linquist wrote: Is there any way to control a gimbal with the remote (pass-through) when not in AUTO mode, and have that control change to the selections that I have chosen in the mission...
View ArticleWindow 10 - not connecting pixhawk 2.4 on either MP or QC
@tonyrjohnson wrote: Hi, I am building a rover using defender tank with skid steering, and as far as I can tell have connected all the essential items. Two things happen. One the pixhawk after a while...
View ArticleClik here to view.
ROS and Raspberry Pi | Tutorial for Beginners
@tiffo wrote: thumbnail.jpg1280x720 144 KB Technically speaking there is no mention of any autopilot in my tutorial. But, as ROS (Robot Operating System) becomes more and more popular, I kinda felt...
View ArticleHelp with airspeed sensor
@Lbarreiro wrote: Hi I’m having trouble installing a airspeed sensor via I2C port on pixhawk cube with the last firmware. I have one as show in ardupilot instructions for plane and followed all the...
View Article