Fatal crash on a tried and tested rig. 4.0.5 / onmibus f4pro / r9mm
@tyantcheff wrote: AP4.0.5 on omnibusf4pro on a ZOHD Dart XL, having flown many times before. Did all the usual preflight checks – control and stabilization direction, gps lock, battery level, radio...
View ArticleCompass working or not?
@jswilson64 wrote: I have a “new” Pixhawk 2.4.8 from an Amazon seller. My older Pixhawk board was getting flaky readings from the Z accelerometer so I replaced it. I’m very much a novice, I build a...
View ArticleHow to make a request for new AIO FC
@chrislinux wrote: Is there a direct way I could ask the developers of this project to add support for a current board? Per my last post I have been using the iFlight SucceX-E F4 with iNav. There is...
View ArticleRFD900UX very hot - is this normal?
@ItsMeAubey wrote: I have an rfd900ux and rfd900x pair. Recently the 900ux has started to get very warm to the touch, but more so when tx/rx lines are connected to it. Is this normal? Posts: 1...
View ArticleMultipoint Radio Control Transmission
@eM.Farih wrote: Hi guys, Is there a radio control / repeater device that supports multipoint network so it could achieve very very long range? Is it possible and reliable? Thanks Posts: 1...
View ArticleClik here to view.
Failed to load module: no module named antenna
@hoss24 wrote: Screen Shot 2020-07-18 at 11.30.02 PM1880×1178 181 KB I am a beginner with MAVProxy. I am successfully able to execute: sim_vehicle.py --console --map Arm the quad, takeoff, etc. Have...
View ArticleFree-fall then crash when flying in Guided Mode
@Notorious7 wrote: I am running ArduCopter master branch V4.1.0-dev (24fccd5d) on omnibusf4pro FC. I have customised the firmware code slightly and made one custom thread running with AP_Scheduler in...
View ArticleClik here to view.
Fix problem and Identifying Esc becouse they are not working properly
@J_B1 wrote: Hello, can anyone tell me more about these esc or what i can do? I bought the esc’s a few years ago and i think, that they were pretty new and good but now i want to reflash them and...
View ArticlePID attachment is needed?
@Sergey_S wrote: Hey guys, I have some issues with my H frame copter (1200x800mm). The copter puts its nose down in an attempt to take off, but if you manage to take off, it gets tilted and crashed....
View ArticleClik here to view.
"Bad terrain or ground data" loading terrain follow mission in plane
@anparkinson wrote: I now have the ‘Bad or no terrain data’ error when planning a terrain following mission in my plane. Terrain following enabled in parameters in mission planner. See screenshots....
View ArticleClik here to view.
Hardware difference between CUBEs
@Tasters_Choice wrote: hi; i’ve been looking at pixhawk 2 CUBE: image654×593 78.3 KB and then noticed that it has changed in appearance to this: image1236×914 112 KB in the websites i visited, it says...
View ArticleAutotakeoff problem with airspeed
@jesus_taax wrote: Hello all, I´ve done hundreds of autotake off with the x5 planes without airspeed. The other day, I decided to install the Measurement Specialties 4525DO. I always do a preflight...
View ArticleClik here to view.
Autotakeoff sometimes turns 180° in the wrong direction
@Rolf wrote: This doesn’t happen every time, maybe every 10th time, but I can’t figure out the reason. Arming_Check is 1 and while arming the airplane is heading in the right direction. If the error...
View ArticleArduCopter to Follow ArduBoat: doable?
@philatSAMS wrote: Hello Everyone, 1st post so hope no typos… I’m putting together an idea to measure air temperature gradients over lochs in Scotland (because science…). I have a working Arducopter...
View ArticleLog Analysis Help: Quad fell out of sky
@dogjutsu wrote: Hi Folks, I’m relatively new to Ardupilot, and am very inexperienced with log analysis. I just had my first fell-out-of-the-sky-like-a-brick crash, and I’m hoping the community could...
View ArticleUploading firmware to Pixhawk 1
@rkprimrose wrote: I have a 3DR pixhawk that I haven’t used for awhile and wanted to load arduplane on it. With Mission Planner 1.3.72 build 1.3.7463.24854 I kept getting no response from board...
View ArticleCan a Servo*_Function be set from LUA script?
@frankw wrote: Is it possible to set a servo function to “disabled” and then back to original function from LUA scripting? I can read the function for a channel but not set the function. thank you for...
View ArticleHow to use flir duo r on pixhawk2
@Ricoman wrote: Can I use the shutter trigger of a Flir duo R camera using pixhawk2 or RC directly using PWM signals? There are 4 lines from the USB port of my Flir camera. According to the manual, 4...
View ArticleFLIR Duo Pro - Camera geotag via Mavlink problem
@cacaroxy wrote: I succeeded to connect Duo pro R and pixhawk cube black with mavlink. I used telem 1 and checked that it was geotagging. But I found several pictures with the same GPS. I inquired to...
View ArticleLUA scripts within SITL simulations?
@Albcem wrote: Is it possible to setup the LUA script environment to test scripts within SITL simulations? How does one do that? Posts: 1 Participants: 1 Read full topic
View Article