Ardupilot for Powered Sailplane
@michaelscote wrote: Hello, I am looking into putting the ardupilot into a powered sailplane. Will this work for a powered sailplane? If so, what is better Ardupilot or Pixhawk? What model of powered...
View ArticleSITL for Ardusub
@jakkala_kalvik wrote: Did anyone try getting SITL to work with ArduSub. I want to simulate an underwater rover I am not sure if I can get SITL with ArduSub working by my self. Posts: 2 Participants:...
View ArticleFirmware version and I2C voltage - APM 2.6
@ph00ns wrote: Hi, I have a APM 2.6 FC that is behaving unexpectedly. I can load the latest firmware (AC3.2.1) but it will not boot (i get the error AP_Baro_MS5611 did not initialize for 1000ms)....
View ArticleGasoline Helicopter Configuration
@Mustafa_Efe_Cetin wrote: Hi, I want to fit my pixhawk to a gasoline powered heli. Could you give me suggestion for configuration? Is it possible to fit or reliable to operate. Posts: 1 Participants:...
View ArticleExternal and internal LED color not the same? plane firmware 3.7.1
@FireFly wrote: External LED on FMU-I2C1 turn blue blink while no TF card, but internal LED on FMU-I2C2 red solid, other color is all the same, is this normal? Posts: 1 Participants: 1 Read full topic
View ArticleMoving from 3.3.3 to 3.4.5
@cookmangr wrote: I have a hexa that i have fly perfectly for a year with 3.3.3 but know i m modified it to a coaxial X8 and i install the firmware 3.4.5Is there something that is a very big change in...
View ArticleHow to install firmware on APM 2.8
@sergi_torrabadella wrote: Hi everybody, I'm planning to start a new project with Ardupilot (Copter) but I'm really new and I'm a little bit lost. I've recently bought an APM 2.8 board on Amazon....
View ArticleInterchange F450 Battery between 3S and 4S
@dasun wrote: Hi, Currently, I am using a 3S battery with my F450 pixhawk quadcopter running with ardupilot 23.4. The problem I have is the flight time is very less around 5-7 mins. So I am going to...
View ArticleMission Planner Icons
@ardisd wrote: Could the rover icon be changed as I am developing a boat Posts: 1 Participants: 1 Read full topic
View ArticleViolent toilet bowling on maiden flight w/ inverted crash
@jprouty wrote: I had a bad maiden flight yesterday. Gear list:- Custom frame, very similar in layout/size/design as the DJI S1000- DJI e1200 Pro propulsion (motor/esc/prop combo). These ESCs require...
View ArticleControlling led's on a pixhawk quadcopter
@alan3113 wrote: Im new here and not sure where to start.But im trying to turn led's on and off with a switch on my TX .Im not having much luck.Im using a Pixhawk flight controller if it was an apm...
View ArticleAutonomous sailboat and path width on long distance course
@Tardis wrote: I am trying to widen the "path" the boat takes to reach a waypoint). Specifically, i am trying to maximize battery by minimizing rudder usage.Currently the boat tracks well and stays on...
View ArticleArduPilot as camera control on uncontrolled flight?
@joatman66 wrote: I am planning a high altitude balloon launch during upcoming solar eclipse for the expressed purpose of photography. I am searching for a solution to keep camera oriented toward the...
View ArticleCopter 3.4+ update, Transmitter calibration issues
@Biswajit1995 wrote: I am facing a weird issue while upgrading my pixhawk firmware to v3.3.3 to v3.4.4, in Radio Calibration, there are no green bars showing to calibrate my transmitter sticks, even...
View ArticleClik here to view.
Voltage on board with power module only 4V whats wrong?
@shyriu42 wrote: hi i m new in this forum and i buy an apm 2.8 with his power module. All was ok until i disconnect usb and i connect the battery. My RC receiver is on alarm because my RC receiver...
View ArticleCopter V3.5 Rc1 Loaded Onto AUAV-X2.1 Flight Controller - Quad Flight
@Jon22 wrote: Not sure whether V3.5 Rc1 release covers the AUAV-X2.1.Loaded Copter V3.5 Rc1 onto my AUAV-X2.1 flight controller via Mission Planner. Noticed in the HUD, pitch appeared as roll and vice...
View ArticleModule SSD1306 Not working on Pixhawk 2.1
@mfbs17 wrote: Module SSd1306 not working on Pixhawk 2.1 but works fine on pixhawk. Posts: 2 Participants: 2 Read full topic
View ArticleAPM 2.6 Compass change - beeping
@jero wrote: Hello everyone,I have one issue with my 2.6 board.I figured out that my external compas is not ok, so Iswitched to the one I have on GPS module.I connected SCA and SCL to I2C port.I...
View ArticlePoshold did not work with 3.5.1
@iseries wrote: Using Pixracer with 3.5.1 and a 250 quad copter3DR GPS Took off in stabilize mode and then switch to Position Hold mode. Copter drifted in the wind in one direction.Reposition the...
View ArticleClik here to view.
Speed and heading error during flyaway event
@rkolyer wrote: Had fly way event where the aircraft speed blew past the commanded speed and the aircraft headed about 90 deg off of the commanded waypoint. The heading bar on the HUD seemed to...
View Article