Pixhawk2 no servo output
@weliwarmer wrote: I'm having problems getting any output to the servos or ESC. I suspect it's a arming error but can't see anything in the logs. [MAV 001:1] ArduPlane V3.8.0beta2 (5baf37f7) [MAV...
View ArticleClik here to view.
PX4FLOW spikes on data output
@Nafnaf wrote: Hi ArduPilot community, I'm trying to install a px4flow sensor on my quad and I've been following the setup guide by ardupilot...
View ArticleWhat is RC_OVERRIDE?
@flyingw wrote: Please indulge my ignorance. I see references to this thing called RC_OVERRIDE, however; I find no related parameters in Mission Planner or ArduCopter. From what I can tell,...
View ArticleUpgrade old 3DR Ardupilot C
@johnelle wrote: I built one of the original 3DR kits which at the time was called the "Quad-C" It was based an Arduino board and I had added an external GPS and a UHF radio link that talked MAVLINK...
View ArticleClik here to view.
RFD900X PPM Pass through test
@PittRBM wrote: Made simple test today by plugging trainer wire from transmitter, which outputs 3 volts PPM, directly to pin 15 of RFD900X.And connect pin 15 of air unit directly to RCIN pin on PH2.1...
View ArticleClik here to view.
Loiter settings for large drone 15 kg
@Winfriedrijssenbeek wrote: We are now testing our drone in auto mode; it overshoots the WP quite dramatically and then also needs time to find the radius of 1 m WP. When it turns it starts brusk and...
View ArticleTaking on Water
@ardisd wrote: Could a sensor be added to a boat that would trigger a return to launch if water is detected in the hull. Posts: 2 Participants: 2 Read full topic
View ArticlePixhawk USB Connectors
@ardisd wrote: Would anyone know the part number and manufacturer of the metal USB socket sold by 3DR as an accessory for the original pixhawk Posts: 1 Participants: 1 Read full topic
View ArticleAerial mapping (MDE Models)
@zuryman1 wrote: MPlannr It's a wonderfull tool, we can do everithing, i'm a Researcher at mexico city, and i was wonderinf if somebody has been working on photogrametric process, or aerial mapping to...
View ArticleGlitches during test flights
@flyingw wrote: I'm running ArduCopter 3.4.5. Using a UHF RC control system talking to a Navio2 through SBUS. In flight, the aircraft suffers glitches in roll, pitch, and throttle. While the...
View ArticleAnyone use Velcro for Sensor attachment?
@jprouty wrote: Using velcro is bad for attaching the flight controller since it can induce some odd vibrations (apparently from wind, according to another thread). Does anyone use velcro for...
View ArticleHow to calibrate mavproxy accelerometer on SITL X Plane?
@bbeallo12 wrote: Hello, I'm using Mavproxy on a Linux Ubuntu virtualbox on Windows 7. And I'm connecting X Plane to mavproxy. When I try to use the arm throttle command it tells me I need to...
View ArticleMissing ESC_CALIBRATION parameter
@Tams wrote: I want to set ESC_CALIBRATION to 3 for calibrating esc according to Semi Automatic ESC-by-ESC Calibration method in this link http://ardupilot.org/copter/docs/esc-calibration.html. But ,...
View ArticleArduino Board Manger?
@iseries wrote: Hey, it's cold and dark outside and I want to hack my Pixhawk. I don't want to run Arducopter but use it as a sketch unit with the Arduino IDE. Is there a board manager for the Pixhawk...
View ArticleConnecting an Edison to a Pixhawk 1
@Rusty_Jones wrote: So, wanting to get my feet wet with companion computers, how do I connect an Edison to my Pixhawks? I am not ready to get the new Pixhawk 2s just yet, so what are the bare minimum...
View ArticleSim_vehicle.py cannot pass through on Windows 7
@xinqunliu wrote: Hello, I followed the instruction of Setting up SITL on Windows. Everything looks good until I run it. When I run sim_vehicle.py, it says "The project was not configured: run "waf...
View ArticleCopter 3.5 Sensor Fusion Algorithms
@tostini wrote: Hello everyone, I've been using Navio2 on a Quadcopter but right now I need to write a report for my project. One of the topics required is to describe the Algorithms used for sensor...
View ArticleDoes Solo run on copter-3.4?
@lroberts wrote: I uploaded copter-3.5 to my solo, but I cannot currently arm solo. Perhaps there are compatibility issues with solo and 3.5 that still need to be worked out. Is it known whether...
View ArticleQuad drops when yawing in alt or loiter mode
@Z9G6 wrote: Hey all! Trying to diagnose an issue here. here is the logs. 2017-02-17 13-56-45.bin (193.9 KB)2017-02-17 13-56-45.log (479.9 KB) the Quad is a 500 sized frame with a mini APM running...
View ArticleIncreasing Payload for 3DR Solo
@Gren wrote: Hi. First time here. Before having to look around for another drone, I'm looking firstly to see if the payload beyond 0.80 Kg can be made possible. I'd prefer to keep the Solo (Brand New)...
View Article