Unable to detect board type
@floaledm wrote: In libraries/AP_BoardConfig/px4_drivers.cpp, any reason to default to an unrecognized board instead of defaulting to a Pixhawk 1? I have a Pixhawk clone (which seems to be fully...
View ArticleCopter 3.4.6 loiter mode with px4flow and lidar
@Hocky wrote: When I use ArduCopter 3.4.6 to test loiter, I found a serial problem1、when you fly in althold first ,you can't swich to loiter mode.2 、when loiter mode fly ，the copter can loiter well.3、...
View ArticleIntel Aero RTF with ArduPilot
@rmackay9 wrote: We've been working a bit on improving support for the Intel Aero RTF developer copter including coming up with good tuning parameters and writing up a wiki page with details of how...
View ArticleNeed support for Here Plus RTK
@ndhuan wrote: Hi, recently I bought a Here Plus RTK set. Unfortunately, I couldn't get RTK fix or even DGPS result from the rover. Let me describe the way I set up Here Plus RTK:- Configure base...
View ArticleArdurover on beaglebone blue?
@monkeypants wrote: I want to run ardurover on a beaglebone blue. So far I have connected over serial with USB cable to brand new device, like this:...
View ArticleFlight Data not appearing on monitor
@onthelearningcurve wrote: I have quadcopter with a Pixhawk PX4 2.4.6 and 3.4.6 firmware, and MinimOSD. The OSD display the titles of the data I wish to have, but no data is returned from Telem2 port...
View ArticleRaspberryPi Camera connection
@impeccableaslan wrote: Hi! What type of connection is needed to connect the raspberry pi camera to Tower? Would radio telemetry do? Posts: 1 Participants: 1 Read full topic
View ArticleNavigate the copter using MAVLink protocol
@Subhi wrote: Hi allI am a newbie so you should be patient with me Does anyone work with Intel Aero drone and try to control it using MAVLink protocol and Ardupiolt?I am facing some difficultie. for...
View ArticleClik here to view.
Finally Spilling the Beans on RTK GNSS
@Robo_Roby wrote: Roby_Ardupilot_Rover.jpg1024x726 1.09 MB Guys, I've never seen an article giving actual RTK GNSS system prices and straightforward explanations of what's important to build a robust...
View ArticleUsing dc to dc converters next to pixhawk
@jimmy wrote: I want to use a dc to dc stepup converter to run my camera in a plane with a pixhawk. Will these modules interfere with my pixhawk? How close together can they be? Any one doing this...
View ArticleInstall note on Tower 4 re 3DR Services
@aritchie wrote: I installed Tower 4 on a Droid Turbo to check out the app and review mission setup procedures on something other than my GCS. I was able to create a survey, but I couldn't save until...
View ArticleI have been out of discussion for couple of years. using old apm 2.5
@nubli wrote: I understand that apm 2.5 is obsolete and cannot use latest software mp 3.XXX ...where can I get older version to install into my apm 2.5.. want to use on plane tq friends Posts: 3...
View ArticleLogging 3rd party CAN msg Arducopter 3.5rc4 or 3.6-dev(master)?
@nbrakeES wrote: I've been struggling trying to configure a Pixhawk/Arducopter system to log a third party CAN message. Problem - I have a single frame CAN message to listen for being output by a 3rd...
View ArticleOverpowered copter drifts in loiter
@rrr6399 wrote: I have a copter that had its MOT_THST_HOVER set to .50, but it appears that only .15 was required. The MOT_SPIN_MIN was set to .15. We noticed that the copter would not maintain...
View ArticleHow can I formatting the TF card Using Mavlink Command?
@kkouer wrote: Hello everyoneFor some reason, i cannot be easily take out of TF card, so I want do that using Mavlink command,is this possible？ Posts: 2 Participants: 2 Read full topic
View ArticleThe copter does not takeoff in Guided mode and EKF_GPS_TYPE = 3 (optical flow)
@dollop wrote: I'm using Pixhawk with companion computer for indoors "missions". I'm familiar with controlling the arducopter with GPS using companion computer with Dronekit and it works good. But now...
View ArticleClik here to view.
Auto-take off veering to right but not in manual (Skywalker on a dolly)
@hangarspace wrote: I've recently configured my Skywalker for auto-takeoffs using an unsteerable dolly from mown grass. With it set into wind, I can take off manually with no heading correction...
View ArticleClik here to view.
Pixhawk2 cable confusion
@mrwooster wrote: Hi, (Context - I have been given a Pixhawk2 as a gift, I have never built a drone or anything RC before, so really being thrown in the deep end, apologies if these are obvious...
View ArticleHexacopter/Pixhawk2.1 - Crash
@guernegor wrote: Hello, I had a crash today with my hexa falling by chance in a corn field.A few seconds before crash I got battery unbalanced messages. When I found the hexa, prop on MOT01 had...
View ArticleGenuine Pixracer in Europe?
@cala2 wrote: Someone know if it`s a shop in Europe that sell genuine Pixracers?I saw someones offering from China but I hope aren't genuine? Posts: 2 Participants: 2 Read full topic
View Article