Quantcast
Channel: ArduPilot Discourse - Latest topics
Browsing all 45630 articles
Browse latest View live

SimpleBGC, MavLink control, Yaw

@ACPUK wrote: Hi all, I am running Copter 3.5 rc4. SimpleBGC Extended 2.62b8 with Mavlink.All works very well, however the gimbal yaw always follows the copter as if it is in follow mode.I have...

View Article


Image may be NSFW.
Clik here to view.

PRX and Obstacle Avoidance

@devanshg25 wrote: Hi all, Im trying to implement obstacle avoidance on a quadcopter I am building (using Pixhawk and Arducopter). Im trying to do obstacle avoidance with 8 horizontal Maxbotix LV EZ0...

View Article


Pixhawk2.1 slow down [custom firmware]

@PittRBM wrote: Please see these videos Normal operation a month ago: Reccently:Note how long Mission Planner took to update radio inputs.Battery voltage reading also slowly ramp up to actual...

View Article

Is APM Planner capable of GPS Inject?

@ahmad.drak wrote: Hi guys, I recently started to move towards APM planner as it sis more suited to work on Ubuntu, as opposed to Mission Planner.I managed to build it and install it on 14.04 (the...

View Article

Continue flight plan interrupted

@pmgarcia wrote: Hello.I would like to know if it is possible to perform a mission with AutoWP-Survey (Grid) in two phases.Many times it is difficult to perform the mission once for battery problems....

View Article


Pixhawk with GR-BD GPS "NEO-M8N"

@bitbeamer wrote: Hello I would grateful if any one could advise me if they have tried using a GR-BD GPS is a NEO-M8N I am trying to setup this GPS up with my pixhawk, I would be grateful if some one...

View Article

Need a firmware for sensor

@hamza_hassan wrote: Hi everyone..!I want to attach a DHT 11 temperature sensor to APM.. But I need it's firmware to get live values of temperature in GUI Please help Posts: 1 Participants: 1 Read...

View Article

WP speed and Circle Rate simultaneously?

@Janne_Johansson wrote: Hello! Is it possible to be able to have both WPSpeed and CircleRate mapped to different channels? I see both available for CH6, but I do not see either in CH9-12? Posts: 2...

View Article


Image may be NSFW.
Clik here to view.

QuadPlane: AUTO VTOL climb suddenly stops

@Anthony wrote: This is in AUTO mode, QuadPlane X8 config. The first command of my mission is a DO_VTOL_TAKEOFF at 75m. What I observe is the vehicle starting to climb and then at 15m or so above it...

View Article


V Tail and Ailerons

@weliwarmer wrote: Hi, Newbie (to V Tail) question... I've lots of experience with delta planes and elevons but not much else. I'm trying to setup a new V tail plane but don't quite understand the...

View Article

Image may be NSFW.
Clik here to view.

QuadPlane: QLOITER tendency to yaw over time

@Anthony wrote: In QLOITER, the QuadPlane seems to yaw clockwise at the rate of 30 degrees per minute, with zero pilot input. Everything in the logs looks "normal" and the IMUs/MAGs are registering...

View Article

Pixhawk 2.1 / GPS Here setup and calibrations

@Bricobrac wrote: Good afternoon, i just acquired a Pixhawk 2.1 with a GPS module "Here" ( bundle available at Skyetech, great serice by the way ) . I was used to Pixhawk 1 and i must admit i am a bit...

View Article

Image may be NSFW.
Clik here to view.

First Phantom FX 61 VTOL

@cala2 wrote: Sin título-1.jpg800x537 242 KB As soon as A. Tridge shows cuadplane I love the new function for my flying wing to get out of the box .It´s my first flyingwing and my first VTOL build so,...

View Article


Required RC radio

@JohnWBlackwood wrote: Can the software be configured to operate without a RC radio RX? Posts: 1 Participants: 1 Read full topic

View Article

Redundancy sensor for Pixhawk (external gyro,acc,compass)

@arzoo wrote: Actually i have a pixhawk . my barometer stopped working . so i am thinking , is there any way to connect multiple sensor via i2c port / serial port like external gyro sensor , compass...

View Article


Beidou Navigation System for Here+ RTK GNSS

@davidshisui wrote: Hello! Is it possible to set Beidou Navigation System for RTK GNSS in the ardupilot firmware? Would like to try how Beidou navigation system performs in China. Thanks. Posts: 2...

View Article

Ch1 and ch3 pwm out

@qdxiatao wrote: i use firmware 3.1, ch3's pwm output will be more 500 than ch1's pwm output, fox example ch3:1750, ch1 1250 steer out:1 Posts: 1 Participants: 1 Read full topic

View Article


Upgrade to 3.4.6 and now have a LOITER issue

@ozsteel wrote: I update my firmware today to 3.4.6 and have a traditional heli (Logo 400) that flies well in Stabilize and Alt Hold but has the "toiler bowel" effect in Loiter. I've calibrated the...

View Article

3.4.5 Enhanced Camera Trigger Precision - Limited to 200 ms?

@adam.g wrote: Hi all, In a similar nature to another post, I’m exploring the potential of using the Swift Navigation Piksi RTK GPS to eliminate the need for ground control points. I’ve run into a few...

View Article

Image may be NSFW.
Clik here to view.

This should be interesting

@timbaconheli wrote: 20170423_112522.jpg5312x2988 3.66 MB This is getting a Pixhawk 2.1..... 20170423_112709.jpg5312x2988 2.69 MB First test bed..... Trex 700 stretched to 800mm swinging the 800mm...

View Article
Browsing all 45630 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>