Pixhawk voltage sensing
@tommal wrote: Hey there, actually if i don't want to use a apm current sensor would it be possible to wire up a small voltage divider and plug it into the voltage sensing port? has anyone done it?I...
View ArticlePoint camera here
@Corrado_Steri wrote: Using point camera here, the software uses terrain altitude as default but it looks like instead of pointing to the ground it uses relative altitude. So for example pointing...
View ArticlePixhawk battery voltage drifting in Mission Planner
@OAPpilot wrote: HiI have a Pixhawk mounted in a FBL helicopter running Firmware v 3.4.6. Using Mission planner v1.3.48. I'm having problems with the battery voltage drifting. I set the battery...
View ArticleAutotune will no longer work
@whakahere wrote: I had autotune working and then on motor broke so it had to be changed out. After that I can't get auto tune to work on any machine (I have two). I redid my transmitter and...
View ArticleClik here to view.
Stop a mission in ArduCopter
@reddylopes wrote: I am trying to develop a way stop a mission in ArduCopter.For now, I saw that there is already a method in AP_Mission called AP_Mission::stop(), that just changes the state flag of...
View ArticleRCOUT not all equal
@rsilk wrote: I am trying to verify if my ESCs/motors are balanced. I did an ESC calibration and the copter seems to fly well. ESC are ZTW Spider 30A opto. Motors are Sunnysky X3108S-720.Checking the...
View ArticleClik here to view.
New Airspeed sensor (MS5525) for ArduPlane 3.8
@Jordi wrote: New Airspeed 03.jpg1229x1191 440 KB We are releasing a new airspeed prototype, we know the hardware might be good, we just need to test more under ArduPlane (only supported on 3.8)....
View ArticleClik here to view.
Going to loiter during auto flight bug
@bendead wrote: Hey guys It's been the second time I had this problem, my copter stop during a survey mission in auto mode and switch to loiter. My setup is an octocopter, controlled by a Dropix from...
View ArticleNTF_DISPLAY_TYPE Missing In 3.4.6
@davidbitton wrote: I have a Pixhawk 1 with Arducopter 3.4.6 installed, and I am unable to find the NTF_DISPLAY_TYPE param. Is this a 3.5.x only feature? Thanks! Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
QuadPlane Help Please
@kikbak wrote: Hello Ardu Masters!I'm hoping to start a conversion of an existing fixed wing to a QuadPlane and am seeking some guidance before I embark on this endeavor. As a disclaimer I have no...
View ArticleAPM Plane/Copter Beta Release Postings
@GregCovey wrote: Hi, I can't seem to find (or am not aware) of the new process for testing and posting findings on beta releases. I have heard mention of APM Plane v3.8 off master and historically go...
View ArticleRead GPS and IMU data form PixHawk to raspberry pi
@tkdronnie wrote: Hello, I am trying to communicate to pixhawk via raspberry pi 2 over MAVLink. I can send commands but i can not read the real time sensor data from the pixhawk. Is it possible to do...
View ArticleAuto-Take-Off Vertical climb then loop and crash
@Captain wrote: HI, We did more than 100 flights with auto take off with a bungee without a single problem, using the pixhawk 1 and the 3.7.0. Lately we have upgraded 3.7.1, we did the first fight...
View ArticleClik here to view.
Multiple flyaways in guided - do I need to tune the EKF?
@Clem wrote: I had 3 successive flyaways yesterday while flying in guided mode. The copter darted towards the horizon at high speed until I regained control by switching to LAND mode.In all 3 cases...
View ArticleHow to clear the Flight Data map screen
@GordonR wrote: I am testing endurance by flying a repetitive flight plan with photographs. After 2-3 iterations the map screen becomes very cluttered and I cannot see where the aircraft is any more....
View ArticleMinim OSD change hardware
@cala2 wrote: Today I was trying to upload latest firm to my minim for a new proyect and find that the latest minim developer announces that He is migrating to this...
View ArticleClik here to view.
Flight log review please
@squirrel_41 wrote: Hi Guys my first post here I wonder if somebody could look at my flight logIts a new quad I just made I was in loiter mode hovering about 1 meter on my front lawn with battery...
View ArticleLoiter (turns) fails to auto sequence
@lobohobo wrote: I need to create missions that will fly through a "survey" of Loiter (turns) waypoints. These missions look correct when built in ground control and are read back correctly from the...
View ArticleClik here to view.
How Can I examine exact EKF Message?
@spirit wrote: 20170514 진동값은 정상이나 3축의 진동값들이 안 맞음.png1366x768 48.1 KB I have EKF-Check 0 and 2 Error Messages. but I have no Idea why this messages pop up. I want to see detail but I cant see it.......
View ArticleRC9 doesn't work if another AUX channel set to 33
@Kirill_Smirnov wrote: Hi there,I have a problem with my Landing gear setup. Will be appreciate for the help.Here 's description of the problem: I have a Pixhawk 2 from the first batch and because of...
View Article