Neutral tilt position for gimbal
@andrewmoni wrote: Should the neutral tilt position for the gimbal be set in degrees, degrees(scaled) or centigrees?? Mission planner appears to want degrees whilst tower seems to require...
View Article[Solved] Fltmode4 RTL instead of auto
@Mo_Freddy wrote: Hi Guys I have a weird issue with flight mode 4 on arduplane 3.7.1 I cannot assign "auto" to mode 4, it reverts to "RTL". while the flight mode screen says "auto" at fltmode 4, the...
View ArticlePixhawk PX4 shutdown (LEDs off & no COM) upon connecting UBEC
@955E479 wrote: Hi - I am trying to run my opto-insulated ESC's from Radiolink Pixhawk PX4. To provide power I am using a KDE UBEC UAS22 , with jumpers set to 6v. However, upon plugging into PX4, all...
View ArticlePixhawk 2 Analog RSSI pin
@yak-54 wrote: anyone know what pin is for Analog RSSI on the new pixhawk 2.1 Posts: 1 Participants: 1 Read full topic
View ArticleFlash new firmware, and mtd seems like being formatted
@liang-tang wrote: sometimes i flash new firmware to pixhawk, then connect pixhawk to apm planner, i lost both params and waypoint...can somebody explain it ? Posts: 1 Participants: 1 Read full topic
View ArticlePixhawk 2 ethernet companion
@Corrado_Steri wrote: Hello, i have a pixhawk 2 with edison companion, from what i understand there is no way to attach the edison to an ethernet port on my onboard router. So i have 2 options i...
View ArticleWind vector calculation?
@robothornet wrote: Hi all, we are doing atmospheric research with UAV at my university. I implemented a Pixhawk 2 in our UAV a short while ago and I noticed that Arduplane somehow calculates a wind...
View ArticleAPM 450 Helicopter Tuning
@rfine7666 wrote: Thanks in advanceNewbie to APM helicopter and need some advice. I have used APM 2.6 and 2.8 board for a few years now on quads and tricopters. I have watched videos of APM...
View ArticleArducopter 3.4.6 vdq210 flipping on take off
@awright424 wrote: I have a vdq210 with 20a littlebee opto esc's and emax rs2206 racespec motors. I have pi0 with a diy pxfmini on it. When I arm to take off it flips. I am also using a 4s lipo. I am...
View ArticleClik here to view.
Pixhawk 2.1 IMU dampening
@timbaconheli wrote: Hello, It was recently explained to me that the Pixhawk 2.1's internal imu dampening is defeated if the unit is mounted on its side. Is this the case? I have a Pixhawk 2.1 mounted...
View ArticleAuto landing gear troubleshooting
@rzzahn wrote: The problem that I am trying to overcome, is the landing gear will not deploy until the FC has booted. The reason this is a problem for me, is that my craft gets stored with the gear up...
View ArticleAutonomous quadcopter
@zubair wrote: I have quadcopter F450 RTF assembledSpecification :Main set size: 490mm x 490mm x 140mmDiameter (length between two motors not adjacent): 450mmPropeller size: 10x 4.5 CW &CCWTake...
View ArticleAC_ROLLPITCHTUNING not working 3.5.0 rc5
@christoph wrote: Status : Mission planner 1.3.48 latest and copter 3.5.0 rc5 Found something weird. I'm trying to do roll/pitch tuning PH by using potentiometer on ch6 (description here :...
View ArticleQUADROTOR CANSAT Challenge using APM2.8
@zaidshakil wrote: Hey Everyone, So i have a cansat that will be deployed to an altitude of 120m by a water rocket. At the apogee, the cansat will be deployed and the rotors of the quadcopter will...
View ArticleQuadcopter cansat deployment using apm2.8
@zaidshakil wrote: Hey Everyone, So i have a cansat that will be deployed to an altitude of 120m by a water rocket. At the apogee, the cansat will be deployed and the rotors of the quadcopter will...
View ArticleAutotune RC5 - important observations!
@pauljatherton wrote: My Tarot Pro Hexacopter has been performing flawlessly on RC5. Tonight I thought I would have a go at Autotune just to test the feature, and it flagged up a couple of very...
View ArticleCannot Build the Code
@Mustafa_Efe_Cetin wrote: Hi there, I am new at coding. I followed the instructions given on the website but I couldnt make it. Could you help me to compile the code on linux (eclipse)? Posts: 2...
View ArticleClik here to view.
4-5 hours VTOL the E1 has been VTOLized
@raptor wrote: The Raptor E1 has been VTOLized not much more to day. There is a penalty of ~ 1 hour in endurance and 0.9 Kg in weight from the VTOL modification. However as the power train was further...
View ArticleFirst time got a wired TF-Card problem
@FireFly wrote: After a flight, I want to download logs, but all logs=0kb from the GCS I can see, so cant download anything! Then I pulled the Card out and read it on PC, there were .bin files in...
View ArticleUDP to MP Connection no heartbeat
@pyrate wrote: Is there a secret to getting it to connect to MPI get wifi, but when I select UDP with correct port it does not find heartbeat Posts: 1 Participants: 1 Read full topic
View Article