Clik here to view.
CADDX GM3 Gimbal not responding
Hello, I have a CADDX GM3 gimbal which i connected to a pixhawk board, but I still cannot control the gimbal, I followed this instructions on how to connect it in multiple serial ports with no...
View ArticleClik here to view.
No output using ThrottleRight and ThrottleLeft, but RC passthrough works
Equipment: Orange Cube+ SmartDrive DC Motor Driver MDDS30 Flysky FS-i6X 10CH Radio Transmitter and Receiver FS-iA10B Problem is that I can only get the motor driver to move the motors by using RCIN...
View ArticleThe future of 32-bit ESCs
Given that BLHeli_32 (#743) stopped development, the drone community is in a weird place. Open-source firmware like AM32 exists which is a sustainable direction. I am looking to buy a new stack for an...
View ArticleArdupilot 4.5.6+OpenIPC+ELRS RadioFailSafe
We have met a FAILSAFE issue using ELRS 3.2.0 915MHz. It might be RC failsafe issue, but we don’t know why: The LOS range is OK SNR is low It was OK, flying with other 3 packs of battery at the same...
View ArticleAnyone using the GPS jamming protection in ublox M10 hardware?
Hello, I’d like to ask if anybody has experience with the jamming protection option in ublox M10 hardware? I stumbled upon it while browsing the configuraiton in u-center and was surprised it was not...
View ArticleFrSky D series telemetry mods
Hi, Here are some extensions I added to the very old FrSky D series telemetry. If you still have such items with you, you may find it interesting to tweak the software and fit your requirements....
View ArticleClik here to view.
Tilt Servo Not Moving in Y3 Drone
I assembled a VTOL drone with a Y3 configuration. The flight controller I used is the Matek F765 WING, and the firmware I flashed is ARDUPLANE 4.5.7. During the tuning process, I found that when...
View ArticleAdding a New Flight Mode and MavLink Message Handling in ArduPlane
Hello everyone, I hope you’re all doing well. I am working on a custom project and have encountered some confusion regarding MavLink messages. To briefly explain the developments I have made so far:...
View ArticleApm 2.8 fc not connecting to mp 1.3.68
the lights r stable, its being detected in device manager, but mp is saying that there is no heartbeat pls help, i tried reinstalling but its the same thing, is there a posibility that the board might...
View ArticleHiring Wheeled Robot Programmer
I am looking to hire someone full time in MN to program, test, and deploy wheeled robots for the construction industry. We have a lot of ideas of robots we want to make happen We want to use...
View ArticleClik here to view.
Dev Call Feb 10, 2025
Release Update github.com/ArduPilot/ardupilot ArduPilot 4.6 issues list opened 12:01AM - 14 Nov 24 UTC rmackay9 DevCallTopic ReleaseAdmin This is a list of issues discovered during ArduPilot 4.6...
View ArticleCan I connect Lidar to GPS2 port?
I have a Pixhawk6-Mini Flight Controller and I was wondering if I can connect my LD06 lidar, which uses UART pins, to the GPS2 port since it has the necessary UART pins? Will I be able to use...
View ArticleBudget RTK components (DATAGNSS NANO RTK Reciever + Helix Antenna combo)
Hello, I am a student looking to assemble an ardupilot-programmed rover that would be operated in high interference zones in close proximity to buildings, and was looking into potential components to...
View ArticleNeed consulting about quad tailsitter based drone
Hello everyone! For quite some time I had been working on my drone based on quad-tailsitter plane. I have gathered few questions connected to the project. I hope that somebody with a good soul might...
View ArticleQuad-band RTK chip quectel LG290P
Ardupilot compatible with Quectel LG290P ? It is quad-band RTK chip so it can receive high accuracy position data without RTK base station. 1 post - 1 participant Read full topic
View ArticleAuto mode with simple avoidance not working with mavlink sensor(Ardurover -...
Hello community, I am feeding Obstacle Distance message from my companion computer(Jetson Nano) via the Obstacle Distance message(330). My ArduPilot is receiving the obstacle message, at the specified...
View ArticleMinimum distance between two beacons for multiple drone landings
Hello! I am currently working on precision landing for multiple drones in a small confined area. May I know the minimum distance required between two beacons such that they land in the area they took...
View ArticleAccuracy of AOA computed versus vane?
May be it is a dumb question what is the difference between AOA calculated by mission planer and an external vane ? Accuracy Thanks 1 post - 1 participant Read full topic
View ArticleMethodic configurator won't connect via TCP (RFDesign TXMod)
I am using the methodic configurator and I am up to test flights. Given the difficulty of physically accessing the cube orange USB port on my drone and the number of test flights I am hoping to do I...
View ArticleAssign two automatic Flight modes to a RC-TX 3position switch?
Is it possible to assign two automatic modes, such as CRUISE and CIRCLE, to the TX 3-position switch? 2 posts - 2 participants Read full topic
View Article