Start Mission Planner with 16:9 aspect ratio for the HUD
@flyingw wrote: Is there a way to set MP so that it comes up with the HUD in a 16:9 aspect ratio instead of the default 4:3 aspect ratio? Thanks, Paul Posts: 2 Participants: 2 Read full topic
View ArticlePay for 22 motor order diagrams for Copter wiki (again)
@rmackay9 wrote: Topic:Replace motor order diagrams for Copter wiki (again) Proposal type: images Description: Pay a designer (identified as part of the competition run after the previous proposal) to...
View ArticleNeed to downoad FW AP 3.6.0 AR 3.0.1 AT 0.8.0
@Stefan_Ditges wrote: Hello cant find the location for download the Firmware above: Need to downoad FW AP 3.6.0 AR 3.0.1 AT 0.8.0 for pixhawk 4 as rover Could anyone give me please the link or the...
View ArticleBattery Monitor Problems on 3.6.3
@cjastennett wrote: Hi all, I am using ArduCopter 3.6.3 (with Mission Planner 1.3.62) on a Pixhawk 2.1 Cube and using the standard Power Module that it comes with, which I underdtand can cope with up...
View ArticleHEavy lift drone circling or yawing on takeoff
@aviontics wrote: The drone was calibrated and everything seems to be in order but the flight test shows it moving around and stabiliing when the Land mode was engaged. You will notice that after the...
View ArticlePixhawk 2.1 Cube and Lidar Benewake TF02
@ecabanas wrote: Hi, I Connected Lidar TF02 to Telem2 port and I have problems to read values from lidar. I connected the wires to the cube port telem2 and I could not see anything in my screen. I...
View ArticleVL53L0X Lidar "Bad lidar heath"
@fs007 wrote: I attached a VL53L0X Lidar via I2C and set parameters according the wiki section of this lidar module. The measuring i can see in missionplanner is correct and very precise.(+/-1cm). No...
View ArticleHow to build the lightest Ardupilot microquadcopter 3-inch "2-stack" frame?
@Hugues wrote: Hello, This is part 1 of a 3" Ardupilot micro quadcopter build, starting by making a custom light frame able to carry all of the electronics and cameras of a full fledge drone: -A F7...
View ArticleWhat does SERVO_BLH_PORT do?
@Anthony_Short wrote: SERVO_BLH_PORT is documented as “This sets the telemetry port to use for blheli pass-thru”. I thought BlHeli pass-thru went over the signal line, not the telemetry line? While...
View ArticleAPM 2.8 with Taranis X8R
@spartan27244 wrote: Is it possible to connect my X8R SBUS to the APM or do I have to do it the old fashioned way using a wire from each channel to each input? I have input signal pins 2&3 jumped....
View ArticleClik here to view.
I can not calibrate the esc
@manotroll wrote: I can not calibrate the esc the light flashes siren more does not make the sound so much around here http://ardupilot.org/copter/docs/esc-calibration.html?highlight=esc and here...
View ArticleDYS XSD 30A V2 BLheli-s esc PWM issue with PX4
@Ian3953 wrote: After passing all the basic setup’s in MP I tried to run up the motors but they only get to about 15%. I had a look at the pwm signal out of the PX4 with an oscilloscope and can see...
View ArticleClik here to view.
RunCam Split Mini in px4?
@manotroll wrote: is it possible to use the RunCam Split Mini in px4? How do I make her serial connection on px4? it can be shared with the miniosd since runcan would practically not receive external...
View ArticleClik here to view.
Pixhawk 4 failing to arm
@lloydrayner wrote: Hi, I am new to the Pixhawk and having some issues getting it working. I am receiving the Preflight Fail: MAG SENSORS INCONSISTENT error. I have already tried the following with no...
View ArticleAgricultural Rover project
@Mimmolo wrote: Hello everybody, I’m really new to this community and I’m quite sure I’m using the wrong place to discuss about my project. I apologyze for that but I’m still a bit confused about the...
View ArticleSerial 4/5 on Cube mini carrier Board
@MartyMcFly wrote: Can some one tell me if the mini carrier board is the same as the normal carrier board and you can use GPS 2 to get serial 4 and 5 many thank’s Posts: 1 Participants: 1 Read full...
View ArticleClik here to view.
Pwm value of channel 3 not changed after shutting down x7 transmitter
@roishachar wrote: Trying to set radio failsafe, but pwm value of channel 3 stay at the same value even after I’m shutting down the taranis x7 transmitter. image.png942x538 49.6 KB Posts: 1...
View ArticleKakute F7 Motor Mapping Wacky
@mrdavidgagnon wrote: I’ve flashed the Kakute F7 with the “latest” 3.7 build online, ran through all the calibrations. I mapped motor4 to servo 6 to make up for the fact that my front left M4 esc pad...
View ArticleControl range pwm channel 5
@manotroll wrote: is there any way to edit these default values? If you want to support 6 modes then the transmitter will need to emit PWM widths of around 1165, 1295, 1425, 1555, 1685, and 1815...
View Article