Hardware Security of Pixhawk Cube
@Vishal_Pal wrote: Hi, I am working on my master’s project of ensuring the hardware security of the Flight Controller. My drone uses Pixhawk Cube as flight controller (Ardupilot as autopilot) with...
View ArticleSkydroid-T12 combination of Data transmission, Picture Transmission and...
@Zhang_Molly wrote: Skydroid-T12 ! It’s Combination of Date Transmission, Picture Transmission and Remote control. 1 Real dual redundant, double antenna and models design. 2 12 channels, supporting...
View ArticleClik here to view.
Trex 600 stretched (700) Pixhawk 3DR tuning
@flyingdragon wrote: Hi everyone, I started posting questions on different thread, and its look like is better to open my own thread just so I don’t take other people threads! I started the build and...
View ArticleClik here to view.
Printable gimbal offered - Sony A5000 +
@Vince_Hogg wrote: Free to download. This gimbal has been working successfully on a few of my drones. Its a bit hardware specific but can probably be modified. I strongly recommend using encoders on...
View ArticleFlip on take off after Chibios latest stable 3.6RC10 upgrade
@Hugues wrote: Hello, I upgraded my octoquad (X8 config, 15" props, Pixhawk1, external GPS+compass) from arducopter/Nutx version 3.3 to the latest Chibios 3.6. Nothing else changed or was modified. In...
View ArticleClik here to view.
Latest long-endurance hydrogen fuel cell drone
@Droneup wrote: Any one intersted in Environment-friendly hydrogen drone？ notuzi H 100.jpg1066×566 95 KB Model: Four-rotor Wheelbase: 1060mm Rack weight: 3.95kg No-load weight: 7.25kg Maximum load:...
View ArticleI need advise Failsafe rule for GCS System using LTE
@BlueMS wrote: Hi, There. I made and wil test My new GCS Hardware System. This GCS is using LTE. So, I need your advise FS. FS_THR_ENABLE values:...
View ArticleClik here to view.
E-Flite mini-Convergence with ArduPilot
@kd0aij wrote: The E-Flite Mini Convergence is a smaller version of the original Convergence VTOL. It came out about a year ago: RCG thread Recently the PNP version has been on sale for only $80, so I...
View ArticleWhat Parameter To Set To Avoid Crash During GPS Glitch Problem or Bad GPS?...
@ton999 wrote: As we know that some times during flying it may happen GPS glitch or bad Gps. So my question is how to anticipate this GPS issue?? What parameter to set to avoid crash if this problem...
View ArticleCompass #2 no detected
@XJ220 wrote: Hi everyone, i want to use 2 compasses for my drone (Dropix + “NEO-M8N GPS + LIS3MDL Magnetometer”). I plug the GPS on the Dropix port. In the “full parameter list” on Mission Planner,...
View ArticleGyroscope readings unit
@faresa2 wrote: Hello all. I was trying to make sense of the gyroscope raw readings in hover. Since roll and pitch are zero (or extremely close to it), one can assume that the rate of change of yaw is...
View ArticleRx rssi no longer working?
@jace26 wrote: I just made the jump from plane 3.8.5 to 3.9.9 and noticed that my rxrssi user-item on the MP HUD no longer works, its just zero’d. No change to my hardware setup or parameters. Using...
View ArticleOpen.HD Video Streaming
@Airpig wrote: Has anyone else tried Open.HD for video stream? Open.HD Wiki I tried it and out of the box it worked with a Pi 3B+ as RX on the ground and HDMI to Display. Still trying to get it to...
View ArticlePixhawk flight control can use two m8p-gps for GPS direction determination?...
@tadiwuh wrote: The interference from magnetic compass has always been a headache. It causes a lot of dangerous accidents. Now pixhawk supports two GPS inputs. Can we configure two GPSs correctly to...
View ArticlePixhawk 2.4.8 not entering into esc calibration mode
@hkk26 wrote: Unable to find the esc calibration setting in APM planner 2.0.26 version. And i’m trying to calibrate pixhack 2.4.8 using this method It seems, Pixhawk not entering into esc calibration...
View ArticleSoftware in the loop (SITL)
@thomaschen61 wrote: hello, can someone enlighten me what is the difference between Dronekit-SITL and the sim_vehicle.py ??? they both seem to do the same, when should one choose one or another ?...
View ArticleMavproxy necessary
@thomaschen61 wrote: i saw example that dronekit ===> mavproxy ===> vehicle is mavproxy really necessary, can dronekit (running on companion computer) talk directly over mavlink to the vehicle...
View ArticleClik here to view.
Hydrogen Cylinder for Hydrogen Fuel Cell UAV
@Droneup wrote: You may have question where to find the hydrogen cylinder, when you want change it or want more spares, here we are 1565861986(1).png913×319 165 KB The cylinder is wrapped by carbon...
View ArticleClik here to view.
Rc_input/RC_output transfer function
@Benykoz wrote: Hey guys, I’m implementing an indoor flight controller (no GPS, position estimated using a tether connected to the drone) on a Navio2 (Cotper 3.6.5) and ROS. I’m using mavros and ROS...
View ArticleClik here to view.
Strange climbrate limit in Guided mode (~5 m/s)
@MikeStros wrote: Hello everyone. I’m using stable flying quadcopter with pixhawk & arducopter version 3.4, flying waypoints in Guided mode, sending waypoint coordinates from external controller....
View Article