NVIDIA Jetson Nano for Pixhawk
@dorukcapraz wrote: Hello all, I have a NVIDIA Jetson Nano. I want to use it as autonomus flight controller. Is it possible like Jetson TX1&TX2? At the ‘Companion Computers’ link, there is no...
View ArticleAdding custom flight mode Qgroundcontrol
@AWE_student wrote: Hello everyone, i got a custom flight mode, which runs fine in in SITL using jsbsim. Now i would like to make it seen in QGroundcontrol to use it in a real flight. However i am not...
View ArticleRover 3.6 release
@kkarl wrote: Hi @ all, have any a Roadmap and a Feature list for the Rover 3.6 ? Kind Regards Daniel Posts: 1 Participants: 1 Read full topic
View ArticleCatastrophic chrash with 4.5 kg Quadcopter X
@BrunoBagarini wrote: Hello guys, Bruno from Brazil here. We were flying a big 4.5kg Quadcopter X with 4 Turnigy G60 500kV and 18x6.5 props for the first time. Something went really bad. All normal...
View ArticleRoadmap Rover 3.6
@kkarl wrote: Hi @ all, have any a Roadmap and a Feature list for the Rover 3.6 ? Kind Regards Daniel Posts: 1 Participants: 1 Read full topic
View Article(FALSE) Low Battery Warning - Still have proper voltage
@TexAcoon wrote: Hello Everyone … Seems I need some help on the battery management… Seems my drone flies for about 2 to 4 minutes at the max - then battery warning sounds … Yet my voltage is still at...
View ArticleBi-diractional communication between ArduPilot and an Android device via the...
@r.rakshak wrote: Note: Not sure if this is the right spot to post this, but I couldn’t think of where else to post it. I am trying the see if it is possible to establish bi-directional communication...
View ArticleOmnibus F4 Pro V2 build by using Zohd Nano Talon
@Nelson_Lee wrote: Hi all master, I am new for plane and just bought this ZOHD Nano Talon and Omnibus F4 Pro V2 try to build Arduplane, after flashed the Arduplane v3.9.9 and connect all the wiring...
View ArticleBreak in latest master CubeOrange
@rbachtell wrote: I just discovered a break in latest master. CubeBlack compiles without a problem but a CubeOrange compile gives this error: In file included from...
View ArticleRCInput_RPI.cpp segfault on Ubuntu, mmap call fails
@f_gh wrote: Hello all, I have an Erle-brain-2 with a Raspberry pi 3. When I run arducopter on the frambuesa Raspbian, it works fine. But when I run it on Ubuntu 18, it ends up in a segmentation...
View ArticleClik here to view.
Flight time calculation error!
@EricGamble wrote: Hey guys, I am returning to Mission Planner but have an issue I cant figure out. The acreage shows correctly, but this is no where near a 47 mile map mission. It shows and 11 hour...
View ArticleTrigger servo on Definite interval
@akhil wrote: During mission planning i want to trigger extra servo regularly at A certain time interval. If anyone know about the parameter tell me If provide the video of setup,awesome Posts: 1...
View ArticleEffect of Dshot ESC brakes on multi-axis takeoff
@okok wrote: The effect of Dshot ESC brakes on multi-axis takeoff, slow takeoff will produce short-term jitter Posts: 1 Participants: 1 Read full topic
View ArticleProper ESC Wiring
@kerrycorcoran wrote: I have the Signal and GND wires plugged into S1 and GND on my Flight Controller. I don’t recall where I saw this, but I made sure I did NOT connect the red wire to the Flight...
View ArticleNew source for waterproof servos, thrusters, and cables/connectors
@Damon wrote: Hi everyone, this is Damon McMillan, the creator of the solar-powered autonomous boat, SeaCharger. I’m going to make a shameless plug for my new business, Blue Trail Engineering. As I...
View ArticleMake px4 communicate only with custom gcs
@Naveen_Raj wrote: how could i create condition such that the firmware connects only with my custom gcs. iam modifying px4 firmware and gcs code side by side and coudnt find any probable answers....
View ArticleClik here to view.
Grayed out options on mission planner
@Mallikarjun_SE wrote: Hey @Michael_Oborne Any idea why some of the options are grayed out? All options work as expected from full parameter list but UI options are grayed out. We are using our own...
View ArticleHow to get time from gps
@Naveen_Raj wrote: how to get time from gps in arducopter. i need to compare time from gps and another parameter. Posts: 1 Participants: 1 Read full topic
View ArticleSpektrum satellite receiver not working with omnibus F4 pro
@Niels_Daemen wrote: I want to use this spektrum satellite reciever with this Omnibus F4 pro v3 (Both flight controllers have the latest arduplane 3.9.9 OFFICIAL firmware installed) When I first...
View ArticleClik here to view.
Use Arduplane as EFIS in experimental or UL manned aviation
@flightzoomer wrote: There was a thread some years ago, asking whether a Pixhawk could be used in a real airplane. I can perfectly understand, why the feedback from the Ardupilot community was...
View Article