Master@59366b0 fails to build
@billb wrote: * 2016-10-13 59366b0 Pierre Kancir Tools: update ci install script (HEAD -> master, upstream/master, upstream/HEAD) I'm trying to build master@59366b0 and it's failing. This is on...
View ArticleCan not connect with Tower 4.0 release
@kraftor_80 wrote: The 4.0 release was pushed to my phone and now I cannot connect. Radios connect (green light on solid) and red heartbeat blinks. When I press connect I see more traffic (red blinks...
View ArticleRecieve data throu usb or serial from pi instead of PWM, APM2.8
@Rarebit wrote: Hello, it is much information to understand the code without a schematic of all the code.I wrote a program to send data with USB Wificards like a RC, with an linux PC as RX and TX....
View ArticleAC 3.4-RC6 360 degrees Lidar support
@mtbsteve wrote: Wow I just stumbled over the RC6 release notes and found the statement about the support of collision avoidance with the SF 360 degree range finder. Where can I find more information...
View ArticleArduplane 3.6 switched to GUIDED after path lost in AUTO?
@Sagaris wrote: Sorry for not providing logs (that's not my plane), but I'll try to describe issue in precise way. My fellow showed me one log with strange behavior in AUTO mode. His plane had lost...
View ArticleServos lock up to max when all servos are used. Voltage spikes across servo...
@Remi wrote: I am trying to configure my Bix3 with a pixhawk, and I have found a very strange problem. I have 4x 9gram metal gear servos for ailerons, rudder and elevator, and 2x 9g plastic gear...
View ArticleCopter-3.4-rc6 available for beta testing
@rmackay9 wrote: Copter-3.4-rc6 is now available for beta testing. It can be downloaded from firmware.ardupilot.org or loaded through the Mission Planner’s Install Screen’s “Beta Firmwares” link. The...
View ArticleBBBmini: Errors during hardware check
@steveb1475 wrote: Hi all, Just noticed that Mirko requested to post support questions here. I just finished building the software and I'm trying to do a hardware check. I get the following errors...
View Article[Solved]Can't get rssi after upgrading Copter-3.4-rc6
@liming wrote: Update: I solved the problem, I use the older Mavlink library. Hi My project need to get rssi value from mavlink. I always use mavlink_msg_rc_channels_raw_get_rssi to get it, but I miss...
View Article3.4rc6 Check mag field error
@AJack wrote: After compass calibration and compass mot went to the filed for a test. "check mag field" all over. Reset compassmot and all went fine. Back at home 100% mag field interference ... maybe...
View ArticleCan't download ArduCopter beta firmware
@govsux1 wrote: Using APM Planner 2.0.24 I cannot load the new FW. The key command is command Q for beta right? When I do that it crashes APM Planner?? Perhaps I'm doing it wrong?? NOTE: The reported...
View ArticleProblem with SysId != 1
@kraftor_80 wrote: I found the problem. If my "sysid thismav" is set to 1, I can connect fine, but my quads all have unique sysid values so that logs go into correct folders.If I change this value to...
View ArticleThe Altitude was different by 20 meters
@Captain wrote: HI, I was flying yesterday and I found that when we put 200 meters altitude on guide mode, the plane was flying at 190m. we tried 320m but it was flying 300m. On RTL mode it was...
View ArticleOcto-x: Behavior after motor los?
@Oisa wrote: Hi,I have an Octo-X and was wondering what happens if I lose one motor or prop. Does arducopter compensate? Posts: 2 Participants: 2 Read full topic
View ArticleAttopilot 180A wrong voltage via telemetry
@ivanv wrote: This is a weird one. I'm using a APM2.5 board with a 3S battery, 3DR 915Mhz telemetry radio and an Attopilot 180A to measure voltage and current. When I am connected to the APM via USB,...
View Article4K Resolution Display
@sFenelli wrote: Hi. I have a Notebook with 4K display and I have problems at looking at the texts in the Mission Planner. How can I solve this? Does anyone had this problem? Thank you in advance....
View ArticleRover tuning parameters
@Noosarover wrote: I am trying to tune the steering on my rover but have not had success. I have followed the "Tuning steering and navigation for a Rover" with limited improvement. Here is a clip of...
View ArticleClik here to view.
CanberraUAV Outback Challenge 2016 Debrief
@tridge wrote: UAV-ME-CSIRO-competition-Canberra-2.jpg4288x2848 1.5 MB The members of CanberraUAV are home from the Outback Challenge and life is starting to return to normal after an extremely hectic...
View ArticleOrthophoto of river mouth
@Noosarover wrote: I am trying to put together an ortho of sand banks at a shallow river mouth so the local coast guard can look for a channel to navigate through to deeper water. I am acquiring the...
View ArticleThermoPilot v7.2 for PixHawk 2
@andair wrote: Does anyone know where I can download ThermoPilot v7.2 ? I'd like to include it onto a new Pixhawk 2. Posts: 1 Participants: 1 Read full topic
View Article