Is SRXL supported?
@Autonomost wrote: I am wondering if the Spektrum protocol SRXL is supported using APM? I cannot find a definitive answer. Thanks for any info! Posts: 2 Participants: 2 Read full topic
View ArticleArduplane 3.5.2 crash strange surge in airspeed before
@hernborc wrote: I´ve assembled a skywalker with pixhawk for a friend that is making agricultural trials to use with a Tetracam camera. Its been working very well before but a few days ago it crashed....
View ArticleMounting compass backwards
@Remi wrote: Due to the cable routing on my plane I need to mount my compass backwards on the tail. Incorporating the already known Roll180 configuration of the compass, i also need a Yaw180...
View ArticleAPM Rover Output Relay
@agreear wrote: As stated in the documentation http://ardupilot.org/copter/docs/common-relay.html "A “Relay” is an digital output pin on the APM or Pixhawk that can beswitched between 0 volts and...
View ArticleClik here to view.
Arducopter Attitude control
@muqing_cao wrote: Dear all, this is a general question regarding the code algorithm in attitude control. I have searched through the previous versions of arducopter and have found the attitude...
View ArticlePixhawk not arming with GYRO 1 SELFTEST FAILED
@kyuhyong wrote: I ordered same l3g gyro (4mm x 4mm one)as used in pixhawk however markinng is different on the chip.On the original pixhawk, it has AGD2 250S is written vs my hardware has AGD8 204(0?...
View ArticleControl pixhawk without remote control
@Yanshof wrote: I build new drone F450 with pixhawk controller. Because of budget problems ... I ran out of money and i could not buy a remote control. I have a lot of experience with software develop...
View ArticleReverse Thrust After Touchdown
@sgloor wrote: Is there any way to add a parameter to give a burst of full reverse thrust after landing. I have an application for a STOL landing with a fast pullup after landing. Full reverse would...
View ArticleCAM messages vs. Images don't match
@coni99 wrote: Hello, I have DIY assembled an Y6 multirotor running on Pixhawk. I've done several test flights with AUTO mission used for photogrammetry grid with 75/75 overlap and using A5000 camera...
View ArticleControl pixhawk without remote control ... only with mission planner
@Yanshof wrote: I build new drone F450 with pixhawk controller. Because of budget problems ... I ran out of money and i could not buy a remote control. I have a lot of experience with software develop...
View ArticleClik here to view.
Vibrations and folding props
@Peterev wrote: I have a Spyder 700 running T-Motor U5 motors X8 with 15" props and I wondered if anybody knows what on folding props causes, or more precisely what I need to try to reduce, vibrations...
View ArticleAPMRover MAVPROXY Not Setting Relay
@agreear wrote: # python mavproxy.py --master=/dev/ttyACM0 --baudrate 115200 http://ardupilot.github.io/MAVProxy/html/modules/relay.html I have successfully set up mavproxy on a raspberry pi and have...
View ArticleCompass Drifting Over Time
@wicked1 wrote: Has anyone noticed their compass drifting? Today during a mission, the copter started toilet bowling, badly. My copter was physically facing north, but in MP, it showed it facing west....
View ArticleShould Pixracer Compass 3 Function?
@wicked1 wrote: After compass calibration, all 3 compasses show a value.However, if compass 3 is enabled I cannot arm. I get the "compass not calibrated" error.As soon as I uncheck #3, I get the beep...
View ArticleCan't see new parameter in mission planner
@hamid_didari wrote: hi guysI have recently added a parameter to Ardupilot using http://dev.ardupilot.com/wiki/code-overview-adding-a-new-parameter/ as a guideline. Somewhere on these boards but I...
View ArticlePlanning curved grid mission
@ILAP1 wrote: Mission planning question: is there a method to plan a grid mission where the parallel grid lines are curved? I want to fly a mission over a road and follow the curves. Setting manual...
View ArticleSwap channels in APM heli
@Vorona wrote: Hi all!I have a trouble.I have very simple joystick without mapping channels and APM mini with AC 3.2.1 - heli. In wiring diagram I see, that connection is not direct (Direct connection...
View ArticleBeginer - How to start the HKpilot 32
@J.Leite wrote: Hi Every one. I am very new on autopilots, I am puting together a boat and after purchase the autopilot, I noticed that I need to upload the firmware. The software offers some otion...
View ArticleClik here to view.
Problmes trying precision Landing with IR-Lock
@umbraclet16 wrote: I want to use IR-Lock to achieve precision landing, but encountered a few problems. I modified the default value of enabled and _type in ACPrecland to avoid modifying parameters on...
View ArticleDataFlash Hardware items
@Fossdal wrote: Hi i am making a LogAnalyzer that parsed DataFlash logs (.bin)I have dificult finding what structure of messages 0- 128 are where can i find them ? i have found these...
View Article