Clik here to view.
Tattu CAN/SMBUS batteries are supported?
@hydropik wrote: Hello, Does these batteries are supported? Tattu Plus 1.0 22000mAh 44.4V 25C 12S1P Lipo Battery Pack with AS150U plug www.gensace.de Tattu Plus 1.0 22000mAh 44.4V 25C 12S1P Lipo...
View ArticleCheck in Joystick to enable as default
@Corrado_Steri wrote: @Michael_Oborne Would it be possible to add a checkbox in the joystick menu that if checked starts the joystick by default when Mission Planner starts? It would be very...
View ArticlePoint to Multipoint Connection to Multiple UAVs with single GCS
@Mustafa_Gokce wrote: Hi. I want to connect multiple UAVs those have RFD900x onboard to use as telemetry link. Is there a way to connect these UAVs using a single telemetry modem (RFD900x) on the GCS?...
View Articlehow to use guide mode and remote control together (dronekit python)
@latte wrote: I want to use the guide mode. In order for the drone to fly to the target automatically And I want to use the remote during the flight To control and avoid obstacles I’m writing a script...
View ArticleClik here to view.
MP waypoint reached spoken message (overcrowd)
@Webillo wrote: Please, observe and listen this video (4K): (Rover followed by three drones, three spanish voices (Pablo repeated), MP 1.3.68.1 build 1.3.7236.10299) The waypoints message is: {sysid}...
View ArticleMission planner error ver. 4rc1
@Marco_fly wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleSupport for Travel to Ardupilot Unconference 2020
@IAMMATT wrote: Topic: Support for Travel to Ardupilot Unconference 2020 Proposal type: Hardware [ ] , Software [ ] , Other [X] : Travel Expenses Description: Peter Hall (@iampete) and I would like to...
View ArticleLidar VL53L1X modes support
@fs007 wrote: Copter 4.0 supports the VL53L1X Lidar and that works well as far as i tested it. This chip has 3 modes: long, medium, short. Long works well indoor, the other ones are supposed to work...
View ArticleRemaining Battery always 100% at start
@alberto.munizaga wrote: Hi No matter how much voltage the battery I connect, the FC always interpretate the battery is fully charged. There is any way to calculate that battery porcentage from the...
View ArticleClik here to view.
Qground control can't received full set of parameters
@xingxing wrote: Hi, I use ULRS( ultimate long rang system) to improve the rang of RC and telemetry signal. Everything works fine except the qground control which is the mobile version. the qground...
View ArticleHelp Using Pixhawk Board and Airspeed Sensor
@samfranklin wrote: Hi, I am a senior Electrical Engineering student working on my senior design project. I am looking for a way to measure airspeed, calibrated airspeed, outside air temperature,...
View ArticleComposite frame
@yrjobjorkqvist wrote: Hello everyone. Have any of your experience building a composite drone frame made of carbon fiber, balsam and epoxy? The purpose is to provide a light and rigid frame for long...
View ArticleClik here to view.
Second flight... and second crash :(
@javigongon wrote: crash.jpg2279×1337 513 KB Hi there! First of all, forgive me for my english, i learned it a lot of years ago and its a little rusty. Ill try to explain: Im new to copters, just...
View ArticleHow to build ArduPlane with library target for Pixhawk and view serial output
@sdeal3 wrote: I am new to using arudplane and have been successful uploading the firmware to a Pixhawk 4 using ./waf and connecting to Mission Planner. Now I was following the tutorial on the wiki...
View ArticleSupport for Travel to Ardupilot Unconference 2020 part 2
@iampete wrote: Topic: Support for Travel to Ardupilot Unconference 2020 part 2 Proposal type: Hardware [ ] , Software [ ] , Other [X] : Travel Expenses Description: Matt (@IAMMATT) and I would like...
View ArticleClik here to view.
The qground control can't received full set. of parameters
@xingxing wrote: Hi, I use ULRS( ultimate long rang system) to improve the rang of RC and telemetry signal. Everything works fine except the qground control which is the mobile version. the qground...
View ArticleFCU time inaccurate?
@rjameson wrote: I’m looking at the SYSTEM_TIME Mavlink message coming from my Ardupilot, and the Unix time field is ~1.3 seconds in the future from the Unix time on my desktop. I would expect them to...
View ArticleDijkstra: cloud not find path
@lumono wrote: When the rover stop in the fence or close the fence, switch to auto model, the rover does not work, stop there. I have to manually move rover to leave the fence. In the case, if rover...
View ArticleFence is unavailable to write to pixhawk 2 when use 915MHz data transfer on QGC
@lumono wrote: When I use 915MHz to write fence to pixhawk on QGC, get error. But if use USB cable, it works. I have to link a USB cable to test rover follow rover running. When switch to 915MHz...
View ArticleClik here to view.
Different Pixhawk Models comparison
@Oscar_Wallace wrote: I have been looking into getting a pixhawk of some kind. But I am not sure which one I should be getting. What I am really asking is what are each one mainly for and what is the...
View Article