Matlab with mission planner
@Engg_Ya_r wrote: Hi All {00} its that possible used matlab to control gimbal or servo connect with pixhawk over mission planner thanks>>> Posts: 1 Participants: 1 Read full topic
View ArticleMatlab over mission planner
@Engg_Ya_r wrote: Hi All {00} its that possible used matlab to control gimbal or servo connect with pixhawk over mission planner thanks>>> Posts: 1 Participants: 1 Read full topic
View ArticleSITL autotest - automated testing
@hanzichi wrote: I would like to run the SITL in an automated fashion where I pipe in a time based set of flight commands from a file. I am familiar with running the SITL through sim_vehicle.py, and...
View ArticleClik here to view.
Sensor Position Offset Compensation IMU & GPS
@Jimmy_Oliver wrote: I have a very large rover that will need the IMU_POS1_X moved drastically. I will also have two (2) GPS units. Do I offset the GPS(s) to the virtual position or the actual...
View ArticleGetting "No GPS" when I switch on my radio
@iforce2d wrote: I built a plane recently that maintains “3D Fix” status nicely with about 9-11 satellites (indoors near a window). However as soon as I switch on my radio the status becomes “No GPS”,...
View Article23kg quad drone crash
@steve wrote: Today we had a 23kg drone crash that flew perfectly 10 missions before this in varying conditions, high wind and low wind it was flying very well. Of course other than the constant...
View ArticleWhy are you still using an airspeed senser
@xingxing wrote: I flew for the first time with flight controller of matek f405 wing in AR wing,i didn’t use airspeed sensor ,so i have to pay much attention to the ground speed,But something magical...
View ArticleClik here to view.
Marketing trial
@tridge wrote: Some people may have noticed that we have finally started to make use of the ArduPilot motto “Versatile, Trusted, Open” on the wiki and discuss forums. The creation of that motto in...
View ArticleBug in AP_NavEKF2_PosVelFusion.cpp ?!
@fs007 wrote: I’m certainly not a skilled c coder, but maybe there is a coding error in AP_NavEKF2_PosVelFusion.cpp tat prevents the rangefinder from being used as primary Alt-Source even if the EK2...
View ArticleSuper simple ardupilot
@Cristian wrote: hello,please sorry if maybe there was this question made already!!!i wanth to build a rover with autopilot software and to have all the gadgets that can suport this software BUT i...
View ArticleArm/Disarm Switch directly on Boat
@sailordude wrote: Hello. I would like to be able to arm/disarm the boat by just pushing a button (on the boat) when I’m out on the water. Then the boat should go directly into LOITER mode. The idea...
View ArticleInterface to Chartplotter
@Finley wrote: I am looking into options for developing an autopilot for a USV. I want to be able to interface the autopilot to a chart-plotter. The chart-plotter would provide steering instructions...
View ArticlePixhawk and Pump connections
@chr89 wrote: Hi All, Im trying to build and Agro Drone with Pixhawk 3 Pro of DROTEK and im facing couple of problems with the pump controller...
View ArticleNOOB UAV project for school!
@Jbird wrote: Hello to all, I am currently a student in college and over heard a proffeser of mine having issues of fly away with DJI products while she is on expedition. So I suggested fixed wing,...
View ArticleClik here to view.
Pololu trex jr dual motor controller dmc02
@Matt_C wrote: I am working on a skid steer rover for indoor use with wheel encoders and a pixracer for a flight controller, running ardurover dev 4.0.1. I am uisng outputs 1 and 2 for throttle left...
View ArticleClik here to view.
DELAY command not executed during mission
@Mirko_Zhou wrote: Dear community, I recently started the testing with the DELAY command for rover, but for some reason it does not work properly. I defined the rover to stop at every waypoint for 3...
View ArticleHow can I see throttle input and output log
@Insik_Kang wrote: Hi, I have tested fixed wing plane yesterday. Then, I want to analyze input and output of throttle on mission planner I have found which indicates throttle output(CTUN - ThrOut) but...
View ArticleList of waf build target compatibility
@RoelHelsen wrote: Hi, I’m building the arducopter code from source, but I’m a bit confused with all the possible board configurations for waf. I can get the list of possibilities with ./waf...
View ArticleClik here to view.
ArduPilot gets https everywhere
@khancyr wrote: https-everywhere-logo.png1200×600 9.21 KB (This post isn’t about the “Https everywhere” tool, I just get the image as it suits the post) Hello everyone, Just a small post to announce...
View ArticleHELP choosing an upgrade GPS from M8N to?
@Xerravon wrote: HI, I recently flashed my M8N’s to 3.01. I then got the GPS signal health bad, also compass errors and more… the quad I’m using it on still has a 3dr pixhawk and it flipped and...
View Article