Clik here to view.
Problem Firmware 3.6.11 (Hexacopter) Horizon 360 degrees spinning
@Amozov_x wrote: Hello. I observed such a problem when connecting power 4 times on different autopilots. Firmware installed everywhere 3.6.11 (hexacopter) Autopilots everywhere Pixhawk mRo. After...
View ArticleHow to enable RF8 to connect to SITL?
@lorbass wrote: I tried to use SITLin order to test my Model development. But as described in the Dev.Wicki for RF9 it does not work for RF8. At this place (>Setting>Physics) it’s nothing like...
View ArticleLIDAR Lite V3 to Pixhawk
@sbofill wrote: Hi Team. I am trying to link up a LIDAR Lite v3 with a Pixhawk 2.1, either thru I2C or PWM. - and the LIDAR is not communicating with the PIXHAWK. At the moment I am going for PWM and...
View ArticleAdd external force to plane
@S_Vinha wrote: Hello, I’m trying to do a new takeoff mode of a plane, using a tether and perform a circular takeoff. The tether would be connected between the center of a circle to a wing of the...
View ArticleSetting up Sensor Offsets Copter 3.6.11
@MerkaTony wrote: I have a copter in which i need to place front of CoG the Cube by 9.5cm and the Here2, about 4.5cm front from the Cube, while also my Z height for cube from Propellers is about 7.5cm...
View ArticleRSSI wrong measures with Pixhawk 2.1 and LRS Thomas Scherrer rx
@tucuman79 wrote: I keep trying to set RSSI with Thomas Scherrer rx (analog RSSI) and Pixhawk 2.1 Cube. First issue, rx manual says RSSI voltage should be between 0.5v to 3.3v (from min to max). I put...
View ArticleLed vermelho acionado
@Clovis wrote: Boa tarde!! Gostaria da ajuda, pois minha apm 2.8, apos um reset ela ficou com o led vermelho piscando e nao pude configurar a mesma, ja troquei o regulador de 3,3v e simplesmente nao...
View Articleupdate version 1.3.68 a 1.3.69
@barros wrote: Hello, I would like to know what is new in version 1.3.68 and 1.3.69 and especially where is the function to make polygons to create missions. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
RSSI missing in new Mission Planner 1.3.69
@Sunlit wrote: After updating Missing planner from 1.3.68 to 1.3.69, all my RSSI data has disappeared under the Quick tab (see pix below). I see that MAVlink processes data, under something called...
View ArticleSpektrum Receiver
@nereus_vessel wrote: Hi everyone. I’m trying to connect a spektrum ar620 to a Pixhawk 2.4.8 running rover v4.0.0. I’m trying to run the radio calibration, but none of the sticks register. I have the...
View ArticlePixhawk 2.4.8, ESC 4 in 1, Flysky 10 channels - Servo lag and can't fly (tip...
@bangity wrote: Hello, This is my 1st quadcopter that I am building. I 3D printed the T4 Quadcopter on thingiverse. I calibrated the ESC and the servos seems to be of the same rpm when I click Test in...
View ArticleVideo tx ? on pixhawk px4 quad
@crgchyn wrote: I have been out of this for a while. running a quad with a pixhawk px 4. Im looking to add a video transmitter that preferably is capable of telemetry also so I can remove my telemetry...
View ArticleClik here to view.
Ardu Copter Build Errors with cygwin using waf
@saddi1991 wrote: I am not been able to compile Arducopter 3.6 using cygwin with waf. followed procedure as per...
View ArticleClik here to view.
Unable to change FlightMode when armed
@cherrypie wrote: Hi there, I have a Pixhawk 2.1 with a here GPS. My problem is that I cannot change the flightmode to AltHold or Loiter when the Copter is armed. When it’s disarmed it works fine....
View ArticleAutotune failed to save new PID with Copter-4.0.0-rc2
@anbello wrote: It is the second time that this happen to me. The first time with a little 3inch with revo-mini so I have no log. The second time happened with a 5inch with Pixracer and so I have the...
View ArticleWhere is “FLOW_enable” in 4.0rc2 Heli FW?
@zhangsir wrote: @rmackay9,@ChrisOlson 4.0rc2 helicopter firmware, where is the parameter Flow_enable? There is also no flight mode FlowHold, can’t traditional helicopters support the use of optical...
View ArticleFailsafe in log file?
@3Denis wrote: Hello, Is there a way to see in the logfiles if and what kind of failsafe was triggered? I faced some situations with failsafe and it would be great to know what the trigger was....
View ArticleThrust Lost in Autotune
@Stefan_Menne wrote: Dear Friends, Today I try to Autotune my big Copter. (Octo, 18inch Props, 4.0.0_dev) Everything went well until suddenly I got the Message ERROR, THRUST LOST and he was...
View ArticleBad AHRS all the time
@pilotltd wrote: Continually getting Bad AHRS - with Rover 4 and Pixhawk 2.1. Been calibrated many times but shows slight jumping on horizon continually. Any ideas? Posts: 1 Participants: 1 Read full...
View ArticleNoob Help! Cannot connect APM 2.6 to QGC
@butchalline wrote: Using QGC 3.2.5, APM 2.6 Tried 9600, 57,600 and 115,200 baud with no joy. Do not know what is loaded onto the APM 2.6 board. What to do? Posts: 1 Participants: 1 Read full topic
View Article