Developing a Flight Controller Board
@harith wrote: Hi all,I would like to build a quadcopter. I am from Electronics background. I have bought all accessories to built one. Now i have to built a flight controller. Can you guys please...
View ArticleMP Stucks at "Getting Param"
@matos100 wrote: Connected the APM 2.6 to the MP via usb and get stuck with the window "Getting Param" Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Problem with signal on servo rail
@vib.mad wrote: I have the same set up on PH1 without problem. I get only signal/power on servo rail Output 1 ..nothing on 2,3 etc...I run MP 1.3.39 with plane 3.7.1 on Fx 61 with elevon mixing.- TX...
View ArticleClik here to view.
GPS_INPUT not working with receiving message from mavros_extras plugin
@yukiya wrote: Now, I'm trying to make new plugin for mavros_extras. I want to make fake gps plugin like a "mocap_fake_gps.cpp". I try to send message "GPS_INPUT message". This is my code to send...
View ArticleClik here to view.
I would like to apply for a BugHunter position - Need tips on hardware
@StenArildHvidsten wrote: Hi. I have +3 years experience in assembly and C on 8 bit µC. I have been using Linux with Debian, mainly, for around 10 years. An of course some scripting, c c++...I am...
View ArticleImproving georef images
@kuspower wrote: Hello Mickael, For improve accuracy of georef images mission planner function, it would be great after estimating timing offset between GPS time and photos to be able to estimate...
View ArticleLog ERR 241-88?
@hpuxionghao wrote: hi, I crash my drone today,when I check the log,I saw a ERR241-88 and ERR183-217.Do anyone know about this?THX Posts: 1 Participants: 1 Read full topic
View ArticleWhat are the Firmware?
@xflyer wrote: What are the firmware listed at http://firmware.us.ardupilot.org/Copter/? How are they to be used?I have a pixhawk in a Y6Thanks,Don Posts: 2 Participants: 2 Read full topic
View ArticleILS landing in Fog
@Marc_Dornan wrote: I thought this was so cool that I had to post it. Pitlab has been doing some very nice work with their new AAT, OSD, AutoPilot firmware. Here is an instrument landing in fog --...
View ArticlePos_z_p < 1,000
@anton610 wrote: Hello,is it a problem to enter a sub 1,000 value to POS_Z_P?My small quad only holds alt with a POS_Z_P value of 0,630. Over this value its pumping. And when i move the stick it...
View Article3DR Pixawk bad ahrs
@qmayberry wrote: I received a new 3DR pixhawk in September and only just got around to installing it. It fails everytime on the accelerometers calibration and keeps telling me bad ahrs. I have...
View ArticleAuto landing gear deploy in RTL - setup confusion (Pixhawk)
@arcticflight wrote: Hi all, new to the forum. Thank you all for your great contribution. I have two copters, one X8 and one hexa (Tarot 680Pro), both controlled by Pixhawk with arducopter 3.4Radio is...
View ArticleMavproxy startup option
@tomekr wrote: Hi AllI have question about mavproxy startup.I installed intel edison on my new pixhawk 2 and debian, wifi works ok. Mavproxy starts with following commandscreen -d -m -s /bin/bash...
View ArticleIs it possible to change the elevator's plane?
@tipehugo wrote: Hi,I have a project which is to make a few tests.I want to make automatic plane’s climbing flights. Each one with a different rate climing with a fixed motor power.I need is the...
View Article2 Motors Run Slower
@pmshop wrote: In a HEX config, motors 6 and 4 (3DR order) run slower than the other 4 almost tipping over backwards.Calibrated the ESCs several times but no change. Flies great though, if I take off...
View ArticleIs there a list of what the commands mean in setup
@smikalow wrote: question about the commands setup in planner Help with setup of planner Posts: 1 Participants: 1 Read full topic
View ArticleHelp with platform choice for flying over fires
@choppedxs wrote: Hi AllI am in the process of finding the best multirotor platform for a fire research project we will be doing next year. The plan is to have multiple drones in the air above a...
View ArticleActivate auxillary servo at specific waypoint
@anparkinson wrote: I want to drop something from my plane at a set waypoint using my Pixhawk but am struggling to see how to do it in the Pixhawk. Can anyone point me in the right direction? Posts: 1...
View ArticleHow do you configure outputs on pixhawk
@scb1957 wrote: I am trying to fire up the aux1 and 2 outputs to give a signal to my 2 axis gimbal, but i am getting nowhere.What do i have to go to in Mission Planner, in order to configure the...
View Article"Terrain data missing" problem in AUTO
@arifg wrote: I got the "Terrain data missing" error on AC3.4.2 even with GCS connected through Mavlink Bluetooth interface and Internet available. In the status window "ter_load" is 336, "ter_pend"...
View Article