3DR Pixhawk Mini?
@MickeM wrote: Hi all! I saw that 3DR have a 3DR Pixhawk Mini in their webshop. How is it compared to the regular 3DR Pixhawk "1" and the newer Pixhawk 2 Suite (Cube + Carrier Board)? 3DR says the...
View ArticleMatlab conversion issues: MSG = 0 and \r\n on final _label
@hunt0r wrote: I've noticed 2 issues with MissionPlanner MATLAB conversion:1) All MSG log messages are 0.(I see that the data is a character string, but the MATLAB equivalent seems to be a double......
View ArticleDEV call 26 Dec 2016 3pm PST = 26 Dec 2016 2300 UTC
@CraigElder wrote: Copter Update Rover Update Release went out ArduPilot.org site https://github.com/ArduPilot/ardupilot/pull/5423) EKF 3 ready pending agreement on how to set the GPS delay for non...
View ArticleCAD Documentaion for custom 3D printed housing
@KirkAndTheKids wrote: First time to this forum, so my apologies if this is a duplicate question.I am planning on buying the Pixhawk2 and put it into a custom 3D printed housing.I can't seem to find...
View ArticleQuad crash (second time) 3.4.4-rc1
@ghostsharp wrote: I crashed a second time, after having changed a motor (M3) and foamed the cables (to prevent any vibration through the wires to the controller), I went to fly a few hours and after...
View ArticleClik here to view.
Logfile variables explaination
@BurnPlane wrote: hi, everyone, where can i find the explaination of logfile's variables for fixed-wing. Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Heading off up to 20 degrees after a spin
@Alexey wrote: Hello, guys!I have a RPi3 with Navio2 + an external compass HMC5843, Copter V3.4.3-rc1 with APM Planner 2.When I rotate my quad by hand on 360 degrees, I see that heading is shifted on...
View ArticleI do not know how to use 4 servos on traditional helicopter
@Cheickh_Barro wrote: Hello everyone,I am a beginner into mission planner and I seek some help. I have a triblade traditional helicopter with 4 servos and one collective (in total 5). in the Initial...
View ArticleAdjusting Pixhawk Mixers
@TexelMicro wrote: Hi, I am trying to use a Pixhawk on a large quad copter with variable pitch. I am having problems getting the ball rolling on adjustment of mixers. I have read that the mixer files...
View ArticleOmission in SITL for windows documentation
@armadillo wrote: Hello, I just came across an omission at the SITL for Windows documentation. The final command of section Install Required Python Packages: python -m pip install --user lxml fails...
View ArticleRSSI over the TBS Crossfire telemetry
@renatux wrote: Hello, Anyone have ideas to get the RSSI value on the Mission Planner over the TBS CRossfire Telemetry ?I've tried for many ways, but nothing yet. Thanks Posts: 1 Participants: 1 Read...
View ArticleEKF2 IMU2 switching to internal compass in Copter 3.4.4
@andyp1per wrote: I'm trying to understand the new goodness of EKF2. In my logs NKF2->MI is always zero but NKF7->MI shows periodic switching to the internal compass late in the flight. The...
View ArticleDoes Tower support wifi telemetry?
@HighFlyer wrote: Does Tower support wifi telemetry? I purchased two wifi telemetry radios after having so many failures of 3DR style 915 Mhz transmitters. I got them both to connect with a PC and...
View ArticleClik here to view.
QGroundControl daily builds support onboard compass cal
@DonLakeFlyer wrote: If you are running a newer ArduPilot firmware in your vehicle which supports onboard compass calibration QGC now has support for it. It's fairly easy to use, just click Compass...
View ArticleLimit maximun power on RC
@J.Leite wrote: Hi Every one,I noted that if I go to maximum speed on the boat, my battery consumption increase very rapidly and my speed does not grow in same way. I would like to ask if some one...
View ArticleCannot Connect APM 2.6 to Computer?
@appleslizer6 wrote: Hi I'm fairy new to apm, but I cannot get my windows 10 pc to recognize the apm. It's not listed in the device manager so my computer for sure cannot see it. Are there drivers for...
View ArticleMumetal --- magnetic interference --- compass calibration
@adnan_ul_haque wrote: While reviewing below arducopter wikis, I have a question to community: will using mumetal (magentic shielding) make the copter more compact and compass safe?. will this help in...
View ArticleUnable to perform "ROI" or "Point camera here"
@massimilianonball wrote: Hi!! As in the object, my quad with a pixhawk running arducopter 3.4.3 stable, can't execute "ROI" or the "Point camera here". The quad perform Loiter, alt-hold and auto...
View ArticleI can't connect my telemetry Radio 433Mhz in Pixhawk Lite
@kintela wrote: Hi I have 2 telemetry radio antenas. One of them I plug it to my PC and I have a com port "Silicon Labs CP210x". The other one I plug it in the telemetry1 port in pixhawk lite. I Load...
View ArticleNew CompassMOT Required After Update?
@Crady wrote: Hi, I just updated my Pixhawk to 3.4.3 and discovered I needed to recalibrate my compass and while the two may or may not be related I have a question: When performing a minor update are...
View Article