Clik here to view.
How to get RSSI displayed on Mission Planner
@new2audru wrote: I have got a pixhawk lite FC and a Frsky L9R receiver which outputs an analog voltage in the range of 0-3.3V to indicate the RSSI. I have checked with a multimeter that the RSSI...
View ArticleClik here to view.
Copter flew away in GUIDED mode
@chev wrote: We're testing an autonomous copter, that is controlled by a Raspberry PI. The mission is, basically, to take of, fly to the destination point, fly back, and land. We had a lot of...
View ArticleTECS tuning settings completely instable
@Maarten_pa0mhe wrote: The Ardupilot firmware project is the best initiative I have seen in years. My problem is not the firmware but my understanding of the tuning. Already for months, and with...
View ArticleCan't get servo to trigger camera. Help!
@Earthman wrote: I have a Hobby King Nova Pro quadcopter that uses an APM 2.5 or 2.6 that I'm trying to setup for aerial surveying. I have installed a 2-axis gimbal, which works fine, and a GoPro-like...
View ArticleSuggestion for platform to work on Autonomous drones
@Vikrant_Fernandes wrote: I have been working with Naza M lite and Arducopter APM 2.6 board. However I wish to work on autonomous drones hence I need suggestions on the best platforms available for...
View ArticleClik here to view.
Latest firmware, Hex flying about 4mts low
@OAPpilot wrote: I have a 680 Hex with a pixhawk which has been doing auto flights as setup.I took it out on a fairly cold day on a planned mission. it flew the coarse very well but i noticed it...
View ArticleNo readings from external compass on Pixhawk
@eclipse wrote: Hi Guys, I'm a bit stumped here trying to get my quadcopter with a pixhawk to calibrate (or even recognize) the external compass. I am running APM Planner on OSX. I bought this Pixhawk...
View ArticleClik here to view.
Big crash, weird radio channels behaviour
@swein wrote: Hi,my APM2.5 with Copter 3.2.1 Quad crashed today, unable to control sligthly touching high voltage powerline and then crashing. By telemetry, it seems like RC malfunction/glitch...
View ArticleMake two flights on a mission
@Gontzal wrote: 100/5000If I have a flight plan and I want to split it into two flights. How can I do it in mission planner?Thank you very much Posts: 1 Participants: 1 Read full topic
View ArticleHow to disable Buzzer in AC 3.4.4?
@R_Q_Robert wrote: Hi All Is there a way i could disable buzzer from MP ?? Posts: 3 Participants: 2 Read full topic
View ArticleAdvanced Parameters disappeared
@GordonR wrote: The latest Mission Planner (plane version) 1.3.43 at first seemed to work fine. But the next time I opened it the Advanced Menu View checkbox on the Config/Tuning page had disappeared,...
View ArticleNew to the PixHawk user family
@Pixdrone wrote: After playing around with Mission Planner and uploading the firmware for the quad copter I have notice that the flight modes pull down are blank. Has anyone seen this or am I missing...
View ArticleTarot 650 new build -newbie would like help please
@MarkL wrote: bin file Hello, I am new to this but built my quad and it is hovering and holding altitude great. I pitch and roll, climb and descend just fine. Also yaw to the right and left but then...
View ArticleBosch I2C BMP180 external barometer / thermo support
@Lance_B wrote: Hey guys. I recently got hold of a couple of these and started looking into the AP_Baro code. Would it be possible to add this sensor in? It appears it functions identically to the...
View ArticleClik here to view.
Tarot650 Quad - Serious jello/vibration problems
@tarot650-pilot wrote: Let`s first start with some hardware: Tarot 650 Sport – modifications: Tarot 680 PRO arms (TL68P05 - 262 mm and anti-vibration motor-mounts (Tarot TL68B33/TL68B34) Tiger MN3110...
View ArticleAdd Sonar Range values to Serial Telemetry Output
@visionscope wrote: Hi there,Looking for a solution to add the value of a sonar range from PIN54 (PWM value) to the Serial Output SR1 or SR2. So I can add it on my OSD panel. At least, I'm looking for...
View ArticleProblem with sabertooth
@Jean-luc_DRONE wrote: Hi, I used since many years a 6wd dagu and APM 2.5 2.6 with no problem, but I'd like to upgrade with a pixhawk.Alas, I've a big problem it's impossible to move forward or back,...
View ArticleClik here to view.
Microquad for mapping
@tommal wrote: Hey there,i was formerly an active drone surveyor. As regulations started to hinder the use of self build drones (3-6 months certification duration and now all registration on hold) and...
View ArticleSignal strength drop-down values all blank
@rsilk wrote: I am using Tower 4.0.0 with Arducopter 3.3. The signal strength menu does not show any values for signal strength, noise, etc. This has worked previously.I recently upgraded to Tower...
View ArticlePixracer with RTK and a new long range radio
@AndrewG78 wrote: Hi.I'm not sure if this is the right category to ask this question, but I was told on rcgroups that I should post it somewhere on this forum. I'm going to try to couple Pixracer with...
View Article