Control gas engine instead of electric
@ofir wrote: When using APM, there is a option to control gas engine instead of electric (ESC) one ? I mean to control servo throttle. Thanks,Ofir Posts: 1 Participants: 1 Read full topic
View ArticleCrash with 3.4.4
@Tobinejumi wrote: Copter takes off in Stable, but ignored switching in GPS pos.hold mode, then rapidly loose height, moves aside and hit the tree. Previous flight with same configuration and 3.4.3...
View ArticleCan some pleas tell me how to get the 3.1
@wacked wrote: I checked out 3.1 and it says page not available.????Thank you. Posts: 5 Participants: 2 Read full topic
View ArticleHow do you get to mandatory (sp)
@wacked wrote: I cant get it passed, firmware. It goes in to 3DR radio. Any ideas? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Fail to disarm after landing
@elkayem wrote: I'm flying AC 3.4 rc4 on a Beaglebone (BBBMINI), pictured below with 3D printed frame. I experienced an unusual landing today. I don't usually land in Loiter, but today I did, and...
View ArticleEZ-UHF Not working
@Chris_B wrote: Pixracer No Channels detected using Taranis with EZ-UHF. Posts: 1 Participants: 1 Read full topic
View ArticleProblems with APM 2.8 without compass GPS mode
@Canarias-Stock wrote: Hello everyone, I've been working with apm for years, without any problems, but now since the month of December 2017, I have a very frequent problem with APM 2.8 without an...
View ArticleWhich GPS unit for Pixhawk cube?
@humanautopilot wrote: This is related to my other topic. Can anyone recommend a plug and play GPS (this is released and available now) for the Cube? I'd gladly buy the ProfiCNC GPS, but there are...
View ArticleRotor Speed Governor
@dmitiy wrote: Hello,I have heard that governor function will be able in 3.4.I would like to know if there are any prospects in this direction. It would be great to use internal governor instead of...
View ArticleMission Planner startup arguments
@Sagaris wrote: Does MP support startup arguments? Can I run MP with joystick or video streaming enabled from start? Can I run MP with automatic connection to specified COM port? Posts: 1...
View ArticleRangefinder Problem in AC 3.4.4
@johnemc wrote: I've just updated to AC 3.4.4 Hexacopter. I have a Maxbotic analog rangefinder attached. When I enable the rangefinder using EK2_RNG_USE_HGT, my altitude and sonar data stop reporting...
View ArticleClik here to view.
MP isn't showing full parameter tree or list, and can't get servo to trigger...
@Earthman wrote: I'm using MP 1.3.43 build 1.1.6202.10835 ArduCopter v3.2.1 (36b405fb) and under Configuration it's not showing the full parameter list or tree. I've tried to uninstall and then...
View ArticleDEV call 16 Jan 2017 3pm PST = 16 Jan 2017 2300 UTC
@CraigElder wrote: Dec Top Contribution Peter Barker Copter Copter-3.5 beta release progress (none :-)) object avoidance AP_Arming PR https://github.com/ArduPilot/ardupilot/pull/5455 SRV_Channel in...
View ArticleQuestion for ArduCopter configuration for pixhawk
@ece_student wrote: Hi, I have a strange question.But, I need it for some reason. I have a pixhawk which consists of two processor, cortex-M4 and cortex-M3.However, if I want to operate pixhawk with...
View ArticleClik here to view.
VTOL "copter" problem ;)
@aamadeuss wrote: Hey Guys,im posting here because its a copter problem with my vtol plane. Problem is yaw, im getting very bad yaw performance, and i think its because some mechanical twist.Motors...
View ArticleStrange autotune behaviour on large Y6 (28in prop)
@JMare wrote: Hi, Come across some strange behavior trying to autotune a big y6 with Pixhawk 2.1. Autotune is setup as a CH_7 option. Procedure was as follows: Takeoff in stabilize, switch to...
View ArticleMag field mistake in auto analysis since Arducopter 3.4.x?
@Hugues wrote: I and a few other people I have made 3.4.X flights with different ships observed systematically in the auto analysis of their logs an indication of this type (this is one example):Max...
View ArticleClik here to view.
Compass Calabration
@ardisd wrote: I am having problems getting the quad to arm with the message compass off sets too high. I am using a 3DR compass the orientation is correct and is mounted on a 100mm carbon mast....
View ArticleCalling for Tridge Parrot disco help
@Saadiq wrote: Hey Guys. We have successfully loaded arduplane 3.7.1 onto our disco and have had a few successful flights(except the bad ahrs warning comes up most of the time) How are you guys...
View ArticleCompass calibration on large vehicle
@Sagaris wrote: I want to do some experiments with Pixhawk on my car. I think it's necessary to make compass calibration to have correct heading, because of large metal body of a car. How can I...
View Article