Bad Logging / No IO Thread Heartbeat
@D_S_S wrote: This message appears on my NP Flight Data screen. (Pixhawk autopilot) What does it mean & what should I do? *Noted that in another thread it was suggested to swap out the SD card....
View ArticlePX4Flow for multiple purposes
@netptl39 wrote: Hi, I have a PX4flow sensor .1. ) I was wandering if there is a possibility to activate the sonar on it for testing purposes only? For work in the city I will surely get a lidar. 2.)...
View ArticleCorrect GPS Time Stamp
@Radja wrote: Dear Community Members, After scanning through all posts I still have some question marks regarding the extraction of the correct GPS time stamp from the Data Flash logs. My observations...
View ArticleCan i use two 3s battery in parallel
@umarufx wrote: hey, i am using apm2.6 Ac3.2.1 Q450 quad frame and using 3s 2200mah 25C Lipo battery. since my flight time is limited to 12--15 min. i have two question.1) can i use two 3s 2200mah 25C...
View ArticleClik here to view.
Pixhawk Ch3_in vs Ch3_out in not linear
@Aero wrote: Hi,I am new to pixhawk and arducopter 3.4. I am testing the copter on ground. what i learnt after arming the copter that the throttle response was not very linear or responsive to...
View ArticleHow to reverse yaw input?
@ayertay wrote: How can I reverse the yaw input from transmitter? Can I do it in Mission Planner? For ArduCopter, not plane Posts: 1 Participants: 1 Read full topic
View ArticleResponsive pitch, slow roll
@vonfrank wrote: Hi, After a major crash with my F550 hexa, I have been tuning to get I flying again, but I keep noticing small problems. Today my autotune results were very low. I tried to revert to...
View ArticleLatest Edison Image
@rbachtell wrote: After flashing the latest image to my edison/P2 I can no longer login to the edison as the previous passwords for initial login and root login are not valid. Is the future plan for...
View ArticleOdd crashes when mavproxy/dronekit connected, 3.5-dev
@fnoop wrote: Hi, I tested some mavlink precision landing code in SITL which seemed OK so I went and tried a couple of flights. I did some flights and landing first normally without the OBC connected...
View Article3DR PIXHAWK HOW TO DO this
@wacked wrote: Can I use a pwm receiver? Posts: 3 Participants: 3 Read full topic
View ArticleParameter Tree not editable in latest beta
@mboland wrote: I just downloaded the latest beta (Help/Check for BETA updates) The Parameter Tree page displays correctly but the values are not editable.Have to go to the full parameter list to edit...
View ArticleAdvance settings is missing
@olboy wrote: I loaded the latest mission planner and went to check on the settings for a few items and I could not find the advance settings. I get to flight modes, basic settings and such but no...
View ArticleOffsetting servos to level them out
@ayertay wrote: Hello everyone! How can I change the initial servo position? My flaps are looking up instead of being leveled with the wing. In KK 2.1.5 in Mixing->Offset I can move servo and set...
View ArticleDid I fry my APM 2.8? PLS HELP
@NRC11 wrote: I made a STUPID mistake by not reading the instructions for powering the APM carefully.I had atttached the power module and BEC from one of the ESCs WITH THE JP1 INSTALLED.I noticed it...
View ArticleObject Avoidance with ZED 3D Camera
@rmackay9 wrote: Here are some videos of a successful test of ArduPilot (Copter)'s object avoidance using a forward facing StereoLabs ZED 3D Camera. The first video is the 3rd person view of the...
View ArticleTrouble shooting erratic divergence along vertical axis
@bd5wingnut wrote: I am fairly new to the multi rotor community, about a year to date, but I have been flying R/C for more than four decades. I am still learning many things about the Pixhawk. Until...
View ArticleClik here to view.
ArduPilot flying on the CL84 TiltWing VTOL Aircraft
@tridge wrote: We did the first test flights of the Unique Models CL84 TiltWing VTOL with ArduPilot today. Support for tilt-wing aircraft is in the 3.7.1 stable release, with enhancements to support...
View ArticleAuto geofencing
@rgillingham wrote: I am new to Arduplane having just found it on the web. I have used geo-fencing as per that found in the HobbyZone sportsman S+ before. With that it worked by applying a fixed...
View ArticleTelemetry Radio status not logged in plane
@Nihal wrote: I'm using plane 3.5.2. Telemetry radio is an RFD900. I have LOG_BITMASK set to log everything. However, when I checked the logs to check the telemetry strength and noise, I didn't find...
View ArticleBug with mission planner 1.3.43
@qmayberry wrote: I updated to mission planner 1.3.43 a couple of days ago and noticed two bugs. 1st, the connection is no longer remembered and always defaults to UDP when started instead of the last...
View Article