How can take raspberry pi images and gps tag them?
@kalabaddon wrote: Hello I am sure someone has done this before but my google/search foo is failing me. All I need to do is send a trigger command accompanied with the gps figures from the...
View ArticleElevon Output on Non MAIN 1&2
@weliwarmer wrote: Hi, ArduPlane 3.7.1 on both Pixhawk1 and Pixhawk2.1 After the Pixhawk2 service bulletin I moved MAIN 1 to MAIN 7 and set the RC7_FUNCTION to 4 (Aileron) but the ELEVON_OUTPUT does...
View ArticlePower Module for Heavy Hexacopter
@4sfaloth wrote: I am trying to find an adequate power module for a heavy hexacopter. Its motors are rated at maximum 30A continuous current, but do not state any information in what regards peak...
View ArticleJoystick Save problem
@Mustafa_Efe_Cetin wrote: Hi, I am flying my quad over joystick. Everything was good so far but mission planner does not keep my joystick settings. I have to repeat all the setups over and over again....
View ArticleJoystick autostart
@Mustafa_Efe_Cetin wrote: I prefer my quad over joystick. Is it possible to activate joystick at the startup of mission planner? Posts: 1 Participants: 1 Read full topic
View ArticleThrottle setup in AC 3.4
@johnemc wrote: My Trex 450 Pro / Pixhawk is finally tuned and flying with Throttle in Ch. 8 Input mode (1) using a throttle curve setup in my radio. I thought that the controller would not adjust...
View ArticleHow to speed up tail servo?
@wacked wrote: Any ideas on how to do this? It works it is just real slow and not at all snappy.It will barley YAW, I am using a PX4.Thank you Posts: 1 Participants: 1 Read full topic
View ArticleLooking for the flown distance data in the log browser
@JeyPi wrote: Hi to all. I have been using the Mission planner for some time, but have not discovered where to look for the flown distance information after the mission is completed.Having flown the...
View ArticleIs it possible to change the current sens pin on a DROPIX ? thanks!
@aamadeuss wrote: Hey guys.i think i fried my current sens pin on my dropix. is it possible to change it to another pin? Posts: 1 Participants: 1 Read full topic
View ArticleCompass Mot on Traditional Heli
@ardisd wrote: How can you do compass mot on a traditional heli or is it necessary Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Paid Help Wanted to complete project
@gsprince16 wrote: I live in Maryland but am sure this could be done online. I have attached a sample drawing of what I'm trying to accomplish with this and need to be done soon. As you can see, I...
View ArticleCan some review a log for me? help me better under stand it?
@Z9G6 wrote: 2017-01-25 14-50-12.bin (904.2 KB)2017-01-25 14-50-12.log (1.9 MB) So could someone look this over and give me an impression of what I need to work on? its a 1.2m 12s hex pixhawk. it flys...
View ArticleGuided flight mode (simple/headless)
@sunama wrote: When I use Guided flight mode, and the copter is travelling between 2 points, before the copter begins the journey, it first turns in the direction and then moves forward. Is there a...
View ArticleUsing empty params of MAV_CMD
@mojojones wrote: I posted this over in dronekit on Stackoverflow but didn't get an answer so I thought I'd try here... I'm trying to use a companion computer to control an external device on a...
View ArticleYAW rate very slow in 3.4.4
@fs007 wrote: Just upgraded my F450 from APM 2.6 to Pixhawk (lite). Installed 3.4.4.Amazing software, except one thing:The yaw rate now is very slow: It needs almost 3-4 seconds to turn 360° with full...
View ArticleWhere is Command delay?
@Dorian wrote: Hello, I have see what the command « delay » in absolute time was not in web site and in MP. Is it planned to hand over this command ? I have a few tests to do on my quadplane and my...
View ArticleCopter Object Avoidance with upward facing lidar
@rmackay9 wrote: A demonstration of object avoidance using a single Lidar pointing forward or upwards. The vehicle is my elderly IRIS and in the first test the LeddarOne lidar is attached facing...
View ArticleH4-X Swash plate
@Mustafa_Efe_Cetin wrote: Hi there, I have a helicopter frame with H4-X swash plate configuration. As you are already know that pixhawk is supportng upto 3 servos. Do you have any suggestion? How can...
View ArticleHow can i get ardupilot code
@umarufx wrote: i am using apm2. 6 copter ac3. 2.1, since ardupilot group is open source, so how can i access and get the prgram code for my firmware Posts: 2 Participants: 2 Read full topic
View ArticleWhy my channel 5 in Mission planner is fluctuating during calibration
@umarufx wrote: hello, i am using apm 2.6 board with firmware ac3. 2.1,FLYSKY 9ch transmitter and reciver. during radio calibration in mission planner when i begins the radio calibration every channel...
View Article