Ch IN, but no CH OUT
@jeraldthompson wrote: Cannot find anything on this problem on line, so here goes: Up until just a day or two ago, I was able to see all the Ch_IN and Ch_OUT traces for roll, yaw, throttle, and pitch...
View ArticleTrimming TLOG or Dataflash log files?
@Pedals2Paddles wrote: Is there a reasonably simple way to trim the TLOG or dataflash logs down? I'd like to chop off any data where the Pixhawk isn't armed. I'm going to try keeping a good data set...
View ArticleHelp : Missing firmware copter-3.4.3 on MP 1.3.44
@Loess wrote: Hi all, Please help,I upgraded to latest MP 1.3.44 and would like to downgrade copter-3.4.5 to copter-3.4.3, in "pick previous firmware" not showing copter-3.4.3. What happened with my...
View Article3DR Telem. Radio v2 & PixHawk
@DoubleT wrote: I bought a 3dr v2 telemetry set to go with my pixhawk - but it arrived with a cable for an APM.Cracked open the case and found what looks like a BF13 6 Position connector. I bought a...
View ArticleJoystick Settings not being saved
@flyingw wrote: I've searched through the various entries on this topic but I cannot find an actual solution other than to upgrade. I believe I have upgraded to the latest Mission Planner version...
View ArticleNew type of auto take off
@wael_a_d wrote: hi I have a crazy Idea to auto launch my airplane (UAV) from a deck of a yacht so the deck is about 18m long and a width of 10mwhat are the best parameters to set in mission planner...
View ArticleClik here to view.
Cannot Calibrate Compass, Either way
@Niels wrote: Hi, building currenly my 4th multirotor and I'm facing some problem I never encountert before. During compass calibration all the points are in one axis. I attache a picture. The first...
View ArticleClik here to view.
Question about RC OUT
@cookmangr wrote: I have a X8 coaxial with sunnysky 3508 700kv motors and 13×5,5 on the top and 12×5,5 on the bottom I want to check the difference at RC Out PWM I see at my logs that there is RC OUT...
View ArticleParrot Disco Firmware
@Firepilot13 wrote: I know that the Parrot Disco has its own proprietary firmware but I wanted to know which flight mode in ardupilot has the closest similar flight characteristics as far a flight...
View ArticleIs Receiver RSSI Supported through SBUS?
@flyingw wrote: I have a receiver that can inject its RSSI onto a channel in its SBUS output. Can I use ArduCopter and Mission Planner to display that value on Mission Planner? If so then what...
View ArticleAdd Weather Data to Ardupilot From Xplane
@bbeallo12 wrote: I need to graph wind speed and direction from Xplane along with rotation rate data from ArduPilot. So I need to add the wind speed and wind direction UDP data from X Plane 10 to...
View ArticleQuestion about state of SITL/HITL
@msadowski wrote: Hi all! I read a bit docs on SITL here. Can anyone of you tell me if all the docs related to SITL/HITL up to date? Is it possible to use SITL with jmavsim? Is there anything in...
View ArticleShutter Config Requirements
@Sully wrote: What is required of a channel to be eligible to be assigned to Shutter on the Camera Gimbal page? I'm working with Copter 3.4.5 If I select any of the drop down choices (Ch9 - Ch14,...
View ArticleHow do I import Mission Planner libraries for Python coding?
@AdamWex wrote: I've been trying to figure out how to code Python for Mission Planner for about 8 hours now. I admit that I'm not a professional or hobbyist coder and that it's my first time using...
View ArticlePros / cons of enabling Galileo satellite positioning on Ublox M8N?
@juzzle1 wrote: The release notes for the Ublox M8N v3.01 firmware states: 'The recommended maximum navigation rate supported is 5 Hz for standard multi-GNSS operation (GPS + SBAS + GLONASS + QZSS)...
View ArticleWhy would this happen?
@wacked wrote: I have a 3DR Pixhawk that will not load FW. It almost gets there than just shuts off. It is a new one out the box. My other ones work good, any ideas? And when I plug it on USB the arm...
View ArticlePixhawk 1 no voltage at Telem ports
@rob215x wrote: Hi all, I've built several quadcopters from scratch using APM 2.6. This is my first Pixhawk build. I have a Pixhawk 1 and I'm trying to connect a set of 3DR telemetry radios. I know...
View ArticleClik here to view.
Mavproxy module
@najam wrote: when i load my module i get this error. can anybody tell me how i can remove this error. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Error in loading mavproxy module
@najam wrote: when i load my module i get this error. can anybody tell me how i can remove this error. Posts: 1 Participants: 1 Read full topic
View ArticleStrange Beep Codes!
@Hein_Du_Plessis wrote: I've had a look at the PIxhawk sounds page but there's nothing matching the below: Any idea what it means? Posts: 1 Participants: 1 Read full topic
View Article