IRIS+ hovered in Loiter mode, FailSafeBatt-1 triggered, copter climbed and...
@Vusal_Jalilov wrote: 1) Describe the problem you are having. What is the expected verses the observed behavior? I was simply loitering IRIS+ approximately 4 meters above ground. I expected failsafe...
View ArticleStick controls wonky after yawing hex when in loiter
@davyg wrote: I took my hex out tonight and did the auto tune, flew it a little while and all was working good... all flight modes worked fine, Loiter was rock solid... it was only when I yawed the...
View ArticleClik here to view.
FG button not Found in simulation Tab in MP!
@ahmed wrote: Hi all , I wanted to use flightgear to simulate my mission , I read the documentation web page , but it explane steps that I didn't find in the mission planner such as ( Start FG Plane )...
View ArticleClik here to view.
Guided takeoff causes crash when R/C is off
@rrr6399 wrote: I've documented the problem here: github.com/ArduPilot/ardupilot Issue: Guided Takeoff Crashes Hexacopter sometimes in 3.4 opened by rrr6399 on 2016-04-09 For firmware versions from at...
View ArticleProblem with Absolute Altitude near the meridian of Greenwich
@SergeB wrote: Waypoint created with MissionPlanner near the meridien Greenwich never have the absolute altitude. Exactly beetwen the longitude 0 degree and 1 degree EST.Files as N48E000, N49E000 ......
View ArticleAPM 2.6 Input channel 1 dead?
@Reggie_Dipo wrote: Hello, Did anyone experienced input 1 from receiver (reciever it self works OK i checked) not working at all I reflashed firmware and was calibrating radio in Mission planner twice...
View ArticleCompanion: Pi 2/3/Zero
@benbojangles wrote: Technical, Code and Hardware questions If you are having issues with Companion: Pi 2/3/Zero development, and would like to discuss code solutions please post your topics here so...
View ArticlePixracer WiFi with mission planner
@douxyeti wrote: Can someone confirm if WiFi connection works with pixracer and mission planner? I can connect to the pixracer WiFi module but mission planner just keep waiting for UDP connection. I...
View ArticleUsing AeroSIM RC with Mission Planner
@rbuav wrote: Hello all. I am working with Florida State University on linking Mission Planner and AeroSIM RC as part of their emerging UAS in Emergency Management program. I found information in the...
View ArticleSame prop broken every flight Im done with it plz help
@Sjuriyan wrote: Hi my Quadcopter sk 450 framePixhawk fc750 kv motor My problem is weird !Almost every flight one of my prop brokenThe weird thing isThe broken prop always Same motor (back left) other...
View ArticleEKF warnings during flight on 3.4-rc1
@kosmik wrote: I had a number of flights today on 3.4-rc1. It was slightly windy day, maybe 5m/s. Everything worked fine, but I did get EKF warnings during flight. I have a custom MinimOSD which shows...
View ArticleClik here to view.
Wing crash after failsafe - what does the log tell me?
@stewlg wrote: I am hoping this crash will prove easy to diagnose. I am not the best at reading log files, and could use some help. The plane is a 60"+ wing running an AUAV-X2 and ArduPlane 3.5.3. I...
View ArticleClik here to view.
Flight Plan layout swapped? How to get it back?
@fireflyer451 wrote: My Flight Plan screen in 1.3.38 has swapped the Waypoints and Action areas are swapped!?! I have no idea how it got that way, or how to get it back to the standard. Please advise....
View ArticleHelp with the History of ArduPilot
@swilker100 wrote: Can anyone help me with the history of the ARDU pilot project. I've used a number of autopilots (Multiwii, NAZA Flip 32, etc) over the years and I think Ardupilot is the best one...
View ArticleClik here to view.
Takeoff and absolute altitude when mission planning
@X1Aero wrote: I'm planning some missions in absolute mode because I have no idea where my LZ will be. First a question about Takeoff and it's fields. All my waypoints are the actual altitude, so...
View ArticleCannot change value in Stabilize R/P
@gfun wrote: I have APM 2.8 . I tried to lift up the quadrocopter and immediately crashed. After i connected to pc I saw that STB_PIT_P and STB_RLL_P set to 0. then i change to 4.500 and save them(try...
View Article3DR X8+ successfuly completed an automission, but lost one prop. Need help...
@Vusal_Jalilov wrote: Hello! X8+ lost a prop in a 10 min mission. Still it perfectly completed it and did RTL. I have checked Auto Log Analysis and apart from Battery Failsafe (which I have no...
View Article(X12?) Dodeca build; connecting PWM multiple ESC's
@alpa2009 wrote: I am buidling a 12-motor coaxial hexacopter and I am thinking on how to connect to Pixhawk. Until now, I just was thinking of using Y-cables to bundle the related ESC's, but this...
View ArticleX8+ Tilted, Drifting and Strange Sound while disarmed
@Vusal_Jalilov wrote: Hello Everybody! My X8+ looks to be tilted to back and left while in STD mode and drifts to the back. I touch NONE of the sticks and it drifts for meters. Video 1. Is this normal...
View ArticleAcro brutally banks backwards
@odus_thesar wrote: Hi everyone,I 3d printed and build a mini quad with an APM 2.6 controller. I tuned it manually, but still have a big problem in acro mode : i'll throttle up to hover, then push...
View Article