Clik here to view.
Bad Logging / LOG_DISARMED = 1 / no CAM/TRIGG logs
@Thorsten wrote: Hi all, Background: Testing camera hotshoe feedback LOG_DISARMED = 1 Pixracer Problem: Both CAM and TRIGG messages are not logged Both CAM and TRIGG messages appear in the FMT...
View ArticleOperation without a gps
@hwurzburg wrote: I would like to use an APM or Pixhawk mini in a small flying wing....no navigation is needed, but just the stabilization modes...ie STAB,ACRO...TAKEOFF would be nice also, but I...
View ArticleRcexel opto ignition kill switch fails while rc5_out = pwm
@garrett_min wrote: RCEXEL OPTO IGNITION KILL SWITCH FAILS WHILE RC5_OUT = PWMRC5_OUT = PWM 2134 - 900 Previous version of Arduplane had no fail with RCEXEL Opto Switch. 3.7 will not switch a NEW...
View ArticleSPI communication between Pixhawk and arduino
@Alessandro wrote: Hi everybody,I would need to send some data (attitude, position and velocity) from the Pixhawk to an external arduino.Unfortunately I cannot use serial4 since it is already occupied...
View ArticlePixhawk ardupilot flight stack
@hudemirc wrote: Hello, I uploaded ardupilot flight stack on Pixhawk and when I open OGroundControl, it gives me error. I've tried pressing the reset button near the Usb plug on Pixhawk, it does not...
View ArticleParameter Add - Rate of Turn
@pmshop wrote: Could a parameter be added to control the rate of turn for waypoint to waypoint?Waypoint to waypoint during ROI?Setting new ROI?Or proceed to next heading after Loiter_Turns? Current...
View ArticleClik here to view.
Does anyone know why mission planner does not connect to Pixhawk? as it...
@vinhk wrote: Posts: 5 Participants: 1 Read full topic
View Article3.4.6 Hexa lost motors output 5 & 6 and crash
@lucamax wrote: Hi , I was testing a Pixhaw replacement and flew around 20 minutes .I noticed that motor 3 (output 6) often had a difficult start .Very difficult it could be an Esc issue since with...
View ArticleClik here to view.
Where to buy female-to-female Futaba connector wires?
@ferocity02 wrote: I am Pixhawk-ing an S1000 and am looking for some servo wires that have Futaba J female connectors (with the guide tabs) on BOTH ends. I bought some JR style wires but these...
View ArticleFlow setting keeps resetting
@ollenorelius wrote: Running Copter 3.5rc2, and both poshold and loiter work pretty well. The issue is that every time I remove power, FLOW_ENABLE is set to 0. No other settings are reset, only this...
View ArticleRPM limited motor control for TECS
@Prototype3a wrote: I've been planning to make the switch to lithium ion power to achieve better range but there is one huge issue. Lithium polymer is 4.2v - 3.7v while Lithium ion is 4.2v - 2.5v so...
View ArticleCopter-3.5.0-rc4 will soon be released for beta testing
@rmackay9 wrote: Copter-3.5.0-rc4 is being released for beta testing over the next few hours (at the time of this post, the auto-builder is still working on it). This has mostly minor bug fixes over...
View ArticleClik here to view.
EMAX 4in1 ESC with Pixhawk1
@adnan_ul_haque wrote: Hello Friends: I am building PixHawk1 F450 quad and have EMAX 4in1 ESC. While following arducopter wiki Pixhawk ESC issues , seems it will not work !?. I did searched following...
View ArticleServo limit for camera shutter doesn't work
@hexapilot wrote: NEED HELP!Changing values for Max Servo-Limit for the camera shutter in ArduCopter 3.4.6 and 3.5 has no effect (servo alwyas moves to the maximum, no matter what I type in)! In...
View ArticleAutotune with sf11 enable it´s possible?
@cala2 wrote: It´s possible to do pos hold autotune with sf11 enabled, or more convenient to disable it for better accurate? Thank´s Posts: 2 Participants: 1 Read full topic
View ArticleClik here to view.
Constant speed between waypoints (survey grid) not working
@Joao_Marques wrote: Hi everyone! Been using mission planner for a few works now and its awesome (was a ex dji ground station user lol)! My only 'problem' is that the drone wont keep the speed that i...
View ArticleMission Planner Loading
@ardisd wrote: Mission Planner 1.3.45 has for some reason got very slow to load (several minutes) on my laptop has anyone any suggestions it has been working well up to about a week ago. Thanks Posts:...
View ArticlePixhawk 2 here compass not working with pixracer
@TTGold wrote: I ordered a new pixhawk 2 Here GPS to hopefully use on a copter controlled by a pixracer. Everything works except for the COMPASS. The LEDS work fine so I know that i2c is working. Does...
View ArticleClik here to view.
Octaquad Plane has no yaw control
@gotmynina wrote: Octaquad Plane with pixhawk 2.1 running patched firmware from Andrew Trigell. started with default pids, but tried changing q yaw parameters, but I more than doubled q yaw P with no...
View ArticleMy Pixhawk 2 Build/Setup Experience (might be handy for anyone needing info)
@Lance_B wrote: After 4 or 5 days of messing with it over the last couple of weeks, I've worked a few things out now and thought I'd share them. My setup is: Hexa 800Pixhawk 2.1 w/ Edison Base running...
View Article