Rethinking the descent rate parameters
@Pedals2Paddles wrote: I had this wild hare of an idea this morning while taking a shower. In pilot controlled modes with altitude control (Alt Hold, Loiter, Pos Hold, Sport), the vertical descent...
View ArticleClik here to view.
Mission Planner 1.3.45 build1.1.6286.16738 missing firmware links
@fireshovel wrote: Would like to install latest Copter firmware but all that is available is Copter V3.4.6. Install firmware screen is missing beta firmware links, etc. Have followed the wiki numerous...
View ArticleComunication between APM2.8 and Arduino
@sergi_torrabadella wrote: Hi everyone, I'm trying to establish comunication between APM2.8 and Arduino using the Telemetry port. I've connected to the RX and TX properly and configured the baudrate...
View ArticleMission Planner Terrain Data Issue
@FalkusKiber wrote: Just some background, I’m flying a 3DR Solo which I used for smaller survey missions or survey missions where something (terrain, obstacles, permissions, etc.) does not allow me to...
View ArticleAutomatic Flight
@WingedWolves wrote: I'm trying to create an automatic flight but without a remote control, do you have any idea? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Higher vibration levels in 3.5 rc3?
@cala2 wrote: I release to beta 3.5 rc3 few days ago my pixracer and find that vibrations go higher, I try roll autotune in poshold (awesome) all go nice and fast but higher vibrations symphtoms...
View ArticleSitl simulation mission planner and xplane
@karthik_pakala wrote: Hi, i have seen the steps to setup a sitl simulation using the xplane and mission planner in the below link. but they dont seem to work. please help me setup a sitl simulation...
View ArticleTwo i2C sonars on Rover
@matislovas wrote: Hi, Maybe someone can give me a hint on how to connect two Maxbotix i2c sonars to Pixhawk? I tried changing the default address of one sonar on the sonar itself and than on Mission...
View ArticleConfusion with LIDAR, EK2_RNG_USE_HGT
@KarlU wrote: How can i tell which height measure is being used? Can i see it in the log somehow?If i set lidar to measure 17.5m then on what logic is the switch done? Lidar measurement or on...
View ArticleAltitude issues with Pixhawks
@anparkinson wrote: I can have one auto flight with my plane where it follows the programmed altitude perfectly and the next it flies way too high and pitches up and down randomly. I have 2 planes...
View ArticleConfiguration of Analog Maxbotic Sonar
@yweidmann wrote: Dear List I try to get an analog Maxbotic Sonar working. I am using the Pixhawk hardware with the firmware ArduPlane V3.7.1. The Sonar is connected to the AUX-OUT-1 of the Pixhawk...
View ArticleLIS3MDL external compass not detected
@thoyo wrote: I have a 3DR PX4 board. Following the instructions from here:http://ardupilot.org/copter/docs/common-installing-3dr-ublox-gps-compass-module.html2 I am able to connect to it the external...
View ArticleClik here to view.
ArduPilot + Openkai + ZED for non-GPS navigation
@rmackay9 wrote: This is the first couple of test flights of ArduPilot (Copter-3.6-dev) paired with LAB enRoute's open source (AGPLv3) vision system called "OpenKai" which uses the ZED stereo camera...
View ArticleCONDITION_CHANGE_ALT-Command
@Jutze wrote: Hi guys, I have updated the Mission Planner Software from 1.3.39 to 1.3.45. Previously I was able to select the Command "CONDITION_CHANGE_ALT" at the Flight Planner. Now it has been...
View ArticleMB_I2C sonar with copter 3.5-rc3
@galdalali wrote: I'm having trouble to activate Maxbotix I2C sonar in this version. It dose not even initialized (there is no sound from the sensor).Works on 3.4.6.I saw that in this branch (3.5) the...
View ArticleHow to connect Lidar Lite v3 to Pixhawk PWM?
@vinhk wrote: Has anyone been able to see data in mission planner after connecting the Lidar Lite v3 to Pixhawk using PWM? I set RNGFND_TYPE = 5; RNGFND_MAX_CM=4000; RNGFND_MIN_CM=20. Posts: 4...
View ArticleHow is Px4Flow with Pixhawk hovering at using Copter 3.5?
@vinhk wrote: I want to know if anyone has been successfully been able to make quadcopter hover using Px4Flow in APM. Posts: 2 Participants: 1 Read full topic
View ArticleClik here to view.
Copter 3.5_Pixhawk_3DR Solo
@cthill24 wrote: I wanted to share some recent findings with anyone interested. See video link. This could breath some new life, add additional utility and open additional configurations to any unused...
View ArticleLanding in FBWA Mode Throttle will not cut
@223Wylde wrote: Last year about mid summer, when landing my fixed wings which are all pushers(I have 3), when throttling down all the way in FBWA mode, I discovered the throttle would not cut, but...
View ArticleVariable Control Rates?
@ferocity02 wrote: What capability is there in Arducopter to adjust control rates while in flight? I have a Yuneec Typhoon H and it allows the pilot to adjust the pitch, roll, yaw, and climb rates...
View Article