RTL Land At Wrong Location After Battery FS
@Mike1 wrote: I have posted this in a couple of other areas and I cannot seem to find an answer. Thought I would try here to see if someone might be able to see something in my logs that I missed? I...
View ArticleHere's a 3D Printable mount for PH2.1 with Edison Carrier
@Lance_B wrote: I wasn't happy with my vibes. After trying several styles of mounting tapes I decided to go this route. This cured it. Cube Mount Folder Posts: 1 Participants: 1 Read full topic
View ArticleRTL not working why not?
@govsux1 wrote: I have a nitro 3 channel fixed wing I've been setting it up and had a successful first two flights. Tried it out... tried FBWA for the first time WOW Awesome!! However when I tried RTL...
View ArticleLow KV Autotune problem
@tomerinbar1 wrote: 2017-04-09 08-42-02.bin (302.2 KB) Hello all, I've a problem with autotune my quadcopter.While in the air in stabilized mode it's wobbling a bit, it's get even worst when trying...
View ArticleClik here to view.
Solo on AC 3.5 RC4 testing results
@mtbsteve wrote: eSolo 3.5 RC4 testing results I spend a couple of hours in the air with Solo today and went through most of its features. I used Solex latest version. Stock Solo configuration with...
View ArticleClik here to view.
Live calibration, off center
@S1CAR1US wrote: Has anyone ever seen this? There's sphere starts to form as usual but does so of center, in the back left corner of the screen, therefore the white dots are never hit and never...
View ArticleUncommanded Yaw with 3.5
@Niels wrote: Hi, i'm really not sure if this is a problem with my rig or if it is some problem with 3.5 rc-2 in my case. I'm getting some strange behaviour during flight. The Hex turns left in the...
View ArticleClik here to view.
Error message: Failed to get rally point
@Dorian wrote: Hello, I have program a new board with APM 3.4.6 and when I connect to Mission Planner, there is an error message : « Failed to get rally point » (just after the connect). I don’t find...
View ArticleProblems with the MB1200 XL-MaxSonar-EZ0 analog sonar and frameware 3.5.0 rc4
@felipeviveiros wrote: Problems with the MB1200 XL-MaxSonar-EZ0 analog sonar and frameware 3.5.0 rc4When I installed 3.5.0rc2 the sonar worked normally but after upgrading to 3.5.0 rc3 the sonar...
View Article3.4.6 - Radio failsafe in AltHold causes direct disarm - bench text
@pauljatherton wrote: I just upgraded my hexacopter to 3.4.6 and before flying, thought I would test the radio failsafe behaviour on the bench. Connected/powered with only USB (which powers the Rx and...
View ArticleCustom parameter settings needed on fresh install?
@glider wrote: So I decided to do a fresh install of 3.5 rc4 and start from scratch. Everything is done except tuning. This is a Y6 (Sky Hero 750). It's been almost 3 years, but the original maiden...
View ArticleAPM 2.8 flight controller doesn’t output
@Munkhjargal_Nymsuren wrote: i built my first quadcopter f450. APM2.8 flight controller, FS-TH9X transmitter, FS-R9B receiver simonc 30A ESC etc. problem is motors not rotating. if connect receiver...
View ArticleProblem when launching APM planner 2.0
@rayane wrote: Hey, Well when i launch apmplanner2.0 the message below shows up< The current user does not have the correct permissions to access serial devices. Use "sudo adduser dialout" and then...
View ArticleWriting Python script to do a mission, need to check for file existance
@Lefteris wrote: Hi there I'm trying to simulate a copter mission in MP. The python script that I'm writing must check for the existence of a file in some specific directory. This file is a QGC...
View ArticleClik here to view.
Data Flash log parameters - documentation does not match data
@Hezi_Ben-Ari wrote: Hi I switched from APM to Pixhawk 2.4.8When looking at the dataflash log the parameters does not match the documentation.For example there are 12 parameters in the CTUN part: And...
View ArticleObstacle avoidance with LiDAR or Ultrasonic
@yweidmann wrote: Dear List Is it better to use LiDAR (eg LightWare SF10) (expensiv but precise) or Ultrasonic (cheap and less precise) sensors for obstacle avoidance? And is there a way of using two...
View Article[SOLVED] 3.5.0-rc4 Looses frame type on reboot
@varesa wrote: I just got a Pixhawk Mini (=pixfalcon?) from 3DR and flashed 3.5.0-rc4 on it. If I try to arm the unit I get the following message:"PreArm: Motor Interlock Enabled" It doesn't matter if...
View ArticleSending data via MAVLink
@Plkonrad wrote: I would like to send information from raspberry pi to pixhawk and then send it to the laptop. My idea is to use UART communication Raspberry Pi <-> PIXHAWK. Then I want to...
View ArticleClik here to view.
Pitch drop when switching to AUTO
@Anto6ka wrote: Hello guys, please help me diagnose the following behaviour: Launching the wing in STAB mode from a catapult, gaining around 40m alt then switching to AUTO, plane drops like 20-30m of...
View ArticleUse Pixhawk with out the SD card
@semo wrote: Hi all , I am using Pixhawk with AP 3.4 for long time using SD Card for data flash logs . but I see some people using it without the SD card when I remove the SD card the pix can't work I...
View Article