Mission Planner 1.3.46.. What has happened to live compass calibration?
@longtallcool1 wrote: 1.3.45 didnt have it so i upgraded again and 46 doesnt have it either. How do i calibrate the compass without the software? Posts: 3 Participants: 3 Read full topic
View ArticleAndroid GCS with follow-me function?
@larsks wrote: I was hoping to experiment with "follow-me" behavior, but it looks like none of the current Android GCS packages are able to do this. Qgroundcontrol never had it, and apparently Tower...
View ArticleAPM:Copter V3.6-dev - potential issues and questions
@Thorsten wrote: Hi all, I want to report a couble of things flying APM:Copter V3.6-dev (f0f7ca23) from yesterday.The problem is, that it is a new build so it might be setup issues. But since the...
View ArticleChanging Circle mode radius while maintaining current center?
@larsks wrote: Has anyone looked into implementing a behavior that would allow the operator to change CIRCLE_RADIUS while in Circle mode (or some new mode) and have the vehicle continue with the same...
View ArticleApplying LOITER mode geofence behavior to other modes?
@larsks wrote: The FENCE_ACTION parameter only supports two values: 0 for "report only" 1 for "rtl or land" However, in LOITER mode, regardless of the value of FENCE_ACTION, there is a third behavior:...
View ArticleHexacoopter 3.5rc4 crash with single motor failure, why?
@imrj wrote: really odd, last week i had a motor failure and managed to land the copter in stabilize, it managed to fly very well and land ok. now yesterday I had another motor fail (not sure if it...
View ArticleClik here to view.
3.4.5 Enhanced Camera Trigger - Selectively generating CAM messages
@adam.g wrote: Hi all, I’ve encounter a strange problem with my Enhanced Camera Trigger selectively generating CAM messages and I was hoping to get some feedback to see if I may be doing something...
View ArticleNo heartbeat packets found
@FlightMonkey wrote: I cant get my pixhawk 2 to connect. Firmware has been installed, reinstalled. Mission Planner, uninstalled, reinstalled. I have tried everything and I cant get the heartbeat...
View Article“Bad LiDAR Health” even if "RNGFND_LANDIND = 1" in arduplane firmware 3.8.0
@FireFly wrote: “Bad LiDAR Health” even if "RNGFND_LANDING = 1" in arduplane firmware 3.8.0 And when landing rangefinder really didnt work! 3.8.0 rc4 Plane Fixed Wing pixhawk...
View ArticleCAN / UAVCAN ESCs
@ACPUK wrote: CAN / UAVCAN ESCs.I know there is several topics on the CAN ESCs. I thought is best to have a fresh DEV topic on CAN ESCs and the development ‘wants’ and ability of them.I appreciate...
View ArticleClik here to view.
MavProxy rise error => MavProxy cannot make connection becouse
@abdelrhmantarek wrote: Posts: 1 Participants: 1 Read full topic
View ArticleMaxBotix for landing flare?
@wkf94025 wrote: I've searched ArduPilot and RCG for information on LIDAR, range finders, MaxBotix etc., and am curious if anyone is using any of the ~$40 MaxBotix sensors for enabling accurate...
View ArticleLoitering performance in RTK Float status
@muqing_cao wrote: Hi all, Recently I have tested RTK GPS using Copter 3.5 firmware. My base has a valid survey and connected to ground station without problem. The status of GPS shown is RTK Float...
View ArticleJoystick control with qgroundcontrol
@derelicte wrote: I know this probably isn't the best place for this question, but I figured I'd ask here first since I already have an account here. I have a rover that I want to control using a usb...
View ArticleClik here to view.
Minimum reliable radius of DO_DIGICAM_CONTROL waypoints (Pixhawk)
@adam.g wrote: Hi all, I was curious if anyone has any experience with how much the waypoint radius of DO_DIGICAM_CONTROL commands can be reduced but still achieve reliable navigation when using a...
View ArticleHow to use rtk gps heading?
@liang-tang wrote: hello , i want to fuse yaw angle by rtk gps heading instead of mag ? what should i do? Posts: 2 Participants: 1 Read full topic
View ArticleQGC Rover, Follow Me
@VonBraun wrote: Follow me mode with rover is working through mission planner but currently there's no mobile app that supports this feature. Is there any chance we could see this feature added to a...
View ArticleHow can I change wifi settings (Edison/Ph2.1/apsync)
@mtbsteve wrote: I have the Ph2.1 along with an Edison board flashed with apsync. Everything works fine and I can seamlessly connect to MP and Tower via UDP. In order to use the wifi connection in...
View ArticleExcited to build my first small rover but need advice from the masters
@ennalta wrote: I am starting on my rover journey but coming at it from a different angle. I have actually built a very large autonomous rover (truck sized) that was all electric and now I want to...
View ArticleClik here to view.
Mission Planner RTK Float vs Fixed
@skyveyor wrote: Hello, I have a Septentrio AsteRx-UAS GNSS installed on my drone. I am injecting a VRS correction via mavlink and monitoring the GNSS performance via Mission Planner and the...
View Article