Clik here to view.
PPK RTK using M8T and RTKLIB
@Thorsten wrote: Hi all, I am running some PPK tests with M8T modules using patch antennas for base and rover (Drotek and CSG Shop). The data, i.e. the ardupilot_dataflash.log.obs and the ubx raw data...
View ArticleArducopters handling of bad baro on PH2.1
@JacksonUAS wrote: Continuing on from the discussion here - https://github.com/ArduPilot/ardupilot/issues/6137 Surely the 2nd EKF should be using the secondary baro, as there is little point in flying...
View ArticlePixRacer 3.4.6 Bad Compass Health on first few boots then Clears
@TTGold wrote: I just finished a new build with a PixRacer installed running 3.4.6. I also am using the new ProfiCNC Here GPS with integrated safety button and Status LED using I2C to run both the...
View ArticlePixhawk 2.1 gyro health
@timbaconheli wrote: Hello,Ive been working with ny new Pixhawk 2.1 on the bench Its been atrached to an 800mm helicopter for a frame. What i keep getting in MP while i test and tune is a message...
View ArticleArduboat self bait drop
@civicoulas15 wrote: Hi,I am totally new in apm and i need some help.I want to make a fishing boat controlled with apm . I have the APM 2.8.. and i need help how i can set it up.The most important...
View ArticleClik here to view.
Cyclic servos end points?
@Implicit wrote: So, I've been going through my setup again and was doing the swashplate leveling as per Rob's video. I then noticed that when I went to min/max, it would no longer be level, so after...
View ArticlePixhawk jumping back and forth between green and yellow
@jacques_eloff wrote: Hoping someone can advise here. I have this issue which sometimes comes up sometimes and it can be very frustrating as it prevents me from arming. Basically the Pixhawk jumps...
View ArticlePixhawk 2.1 power questions
@timbaconheli wrote: Hello, So while on the bench im noticing that the pixhawk seems to send power to the servos even when just hooked up to the usb? Also, im running HV to the servo rail for my...
View ArticleStart Mission from QGC
@lobohobo wrote: Hello All, I'm new and am trying to understand how to start a mission. I created a flight plan, sent to vehicle, and verified that it was uploaded. I then switch to auto mode and my...
View ArticleStable Altitude During Flight
@lobohobo wrote: I'm trying to fly a low-level grid while maintaining a stable AGL. I'm using an F450 with the old PixHawk. The copter slowly loses altitude until reaching the next waypoint. I'm...
View ArticleCannot control servo in PixRacer via RC channel
@Frontier wrote: Hello, I am using a PixRacer on my S500 quadcopter running ArduCopter 3.4.6. The 5th pin of the PixRacer is connected via a signal line (signal & GND) to a Firefly Q6 camera. What...
View ArticlePIxhawk log help
@jtroutt19 wrote: Hey guys, so I finally got new ESC Hobbywing xrotor 40a. I can finally get my quad in the air but I am now having new issues. Once it gets in the air if I leave the throttle stick at...
View ArticleDoes motor order matter - CCW - CW - CCW - CW vs CW - CCW - CW - CCW
@mrwooster wrote: Hi, All the diagrams I see (e.g. http://ardupilot.org/copter/_images/MOTORS_QuadX_QuadPlus.jpg) show motors 1 and 2 being CCW and motors 3 and 4 being CW I have motors with self...
View ArticleHow To setup Transmitter with auto center-throttle with apm to fly like dji?
@rikiatsauri wrote: hello,I have a FlySky i6s with auto center-throttle. I don't want to remove the spring. I just enjoy the dji mavic pro experience to fly with only throttle up or down slowly to...
View ArticleSurvey grid with spinning waypoints
@lobohobo wrote: Is there a GCS out there that supports a grid where I spin (1-2x), then move a set distance, spin, move, spin, etc? If not, does this sound feasible to build myself? Posts: 1...
View ArticleUpgraded to 1.3.47 from 1.3.46 and now it won't work without an internet...
@ozsteel wrote: I don't have internet or phone coverage at my flying field and so prefetch the maps before I go out. After upgrading to 1.3.47 I can't use Mission Planner at the field because I don't...
View ArticleClik here to view.
First Flight & some issues with X8. Need help analysing logs!
@o_zoeller wrote: Hi all, I tested my X8 this morning. I originally planned to do a test flight, then AutoTune, but cancelled after the first one as I experienced some issues. Build: F2X8 Frame...
View ArticleRTK using Ublox evaluation kit
@Niels wrote: Hi,just want to know if anybody does this so far. Looking to buy the C94-M8P evaluation board from ublox to get a second gps on my Pixhawk. Is this working with either Mission planner...
View ArticleProblem in Loiter T-Rex 500 PRO installation 9Dsmart P9X AC3.4.6
@mvpolushin wrote: Guys help, please, I configure my helicopter. What am I doing wrong? The helicopter jumps up and down, does not behave stably, turns around its axis and makes a funnel. Thank...
View ArticleMissed green line Rc calibrarion screen?
@e72x wrote: Latest M.P. and beta does not show green line in RC calibration window ? Posts: 1 Participants: 1 Read full topic
View Article