Descent issues in LOITER/POSHOLD-Mode
@bjoern79de wrote: Hi, already with my last copter I observed high descent rates on fast movements. I thought it was a little bit underpowered.But now my current copter is kind of overpowered (in...
View ArticleHow I can simulate the diferencial efect on each axis of the car?
@Dani_Guerrero wrote: Hello everyone , I have seen that the drone can be controlled very easily each engine , and so I decided to make a car with an engine on each wheel. I'll use ESC car for it. go...
View ArticleAuto Mission unexpected RTL
@dkemxr wrote: I had an odd occurrence during an Auto Mission last night. 2 minutes or so into the Mission, beyond control and telemetry range, it switched to RTL ."Continue with mission in Auto" is...
View ArticleClik here to view.
How to use Precision Landing feature with companion computer?
@HjorturG wrote: Hi everyone. I'm trying to use an on board Raspberry Pi with dronekit python API and camera to land on a target. I am using a Pixhawk with Copter 3.4 with precision landing enabled...
View ArticleTrouble Writing Partial Mission
@jmillwood wrote: I am trying to write a partial mission list to a SITL instance of ArduPlane (3.6beta, I don't thing the version really matters though) and it does not seem to be asking for all of...
View ArticlePlane 3.6.0 released
@tridge wrote: The ArduPilot development team is proud to announce the release of version 3.6.0 of APM:Plane. This is a major update so please read the notes carefully. The biggest changes in this...
View ArticleAbout the Plane 3.6 category
@tridge wrote: (Replace this first paragraph with a brief description of your new category. This guidance will appear in the category selection area, so try to keep it below 200 characters. Until you...
View ArticleEsc calibration not uniform oneshot 125
@cala2 wrote: I calibrate the esc two times but when I check results, when armed, two motors become spinning and the other two only spin when I raise throttle, If I see BHeli suite I found ppm min and...
View Article3.6 supports Camera trigger?
@Kyomo_Jung wrote: Thanks so much Plane Dev team ^^ I've tested cam trigger by clicking "Trigger camera now" on MP but It doesn't work. I found this trouble with 3.6 beta and same issue with 3.6. Is...
View ArticleTuning Advice Needed for Quadplane Please
@jacques_eloff wrote: Hoping for some guidance here: I’ve done some basic tests on my Quadplane in rotary wing mode (no transition as yet) and I’m looking for some tuning tips. Whilst I have 3 fixed...
View ArticleClik here to view.
MAVLink Step by Step
@Pedro_Albuquerque wrote: MAVLink - Step-by-Step by Pedro Albuquerque (still in progress)This post result from my struggle to find information about the subject to understand the concept, and...
View ArticleHelp request for a wildly misbehaving pixhawk quad - EKF errors
@RustyToad wrote: Hi all, I've just had two very hair-raising flights. Here is a FPV recording of the particularly bad section of the second one. Note the climb rate (middle left), altitude (top...
View ArticleRadio telemetry linked but not able to transmit
@Hugo_Ramos wrote: I bought a hextronik telemetry 433Mhz kit and it being impossible to link, The green led is solid when both units (the ground station and the air or conected to the AP2) and if i...
View ArticleTrigger Camera NOW not working in mission planner
@TenboAir wrote: Continuing the discussion from Camera Trigger IR: Hey, did you figure this out? I previously had a Sony Nex5A triggering via servo with a strattosnapper trigger, but recently updated...
View ArticleHK Pilot Mega 2.7 Issues with Firmware? APM Planner 2.0?
@Highpocketse5 wrote: I have had numerous issues with my quad after updating to the latest firmware and software. Nothing is showing in the Standard Parameters Tab and now I get a pre arm check...
View ArticleLost throttle control in manual mode - full throttle!
@RRacer wrote: Hello all,I've returned to RC from a 25 year break, and have been doing LOS flying with helis, planes and small quads.This winter I got a Pixhawk that went into a Bixler 3. The Bix3...
View ArticleApm to pixhawk nightmare
@mbu10 wrote: Well been using apm for years all good.Decided to go to pix hawk for a refresh.And it flyers well in stable mode.Now loiter... The pixhawk comes back with compass varience. And tried and...
View ArticleHeli servo output problems
@ThomasH wrote: HelloI've started to setup a 450 and a 500 with APM 2.6. I think i've connected input and output correctly. Unfortunately I cannot get the input signals to move the correct servos. Ch2...
View Article3.6, Elevons - Mixing_Gain/Mixing_Offset, Can't get proper throw
@bchristal wrote: Something changed in 3.6. When I setup a plane using my same parameters from 3.5 I don't get enough elevon throw when I pitch and roll the airplane. The TX response is fine. Just the...
View ArticleLOG of a very mysterious crash
@shakys wrote: Hello everyone:Today I flew again my quadcopter after 6 months of getting new parts from another crash (also due to an undetermined cause) in January. The drone I flew today had new...
View Article