Pixhawk Cube GPS Wiring..?
@spirit wrote: I'm using Pixhawk Cube and Ublox M8N Clone. in GPS Port I connected 4 wire for GPS and 2 wires for compass. not connected in I2C Port is it right? do I have to use 3 wires for...
View ArticleMission Planner 1.3.48 Stable - Joystick BUG (Beta works!)
@Artem_Bulashev wrote: Hi! Wanted to let people know that my Logitech RumblePad 2 stoped working with update to latest stable 1.3.48. It shows up in Joystick selection dropdown menue, but "Enable"...
View ArticleClik here to view.
ArduPilot monthly update for May 2017
@rmackay9 wrote: May2017-partnersMtgPic.jpg1108x690 71.1 KB Here is the ArduPilot monthly update for May 2017 which Tridge and I (and a few others) to our Partner companies this morning. Thanks very...
View ArticleClik here to view.
What does this error message means?
@spirit wrote: ublox.png1366x768 532 KB I'm using Pixhwak cube. is GPS Module corrupted? I didnt touched anything. I used it normally with apm and pixhawk. Posts: 2 Participants: 1 Read full topic
View ArticlePre-flight Calib using Tx
@GertJL wrote: Hi, I intend to upgrade from 3.3.3 to the latest stable client. In MP, prior to flight, I always use the Action/PreFlight-Calibration priorto take-off. My understanding is, for one,...
View ArticleAC3.5-rc5 ESC calibration problems if not using safety switch
@rmackay9 wrote: There were definitely some problems doing ESC calibration on Pixhawk and Pixracer (and probably all boards actually) if there was no safety switch attached. I've spent some time and...
View ArticleI can't control simulated vehicle from mavproxy
@MaStrz wrote: Hi, I have problem with control of simulated vehicle. I run SITL by: dronekit-sitl copter --home=-35.363261, 149.165230, 584,353 , next I create :mavproxy --master=tcp:127.0.0.1:5760...
View ArticleSwitch Arming in APM
@Shlok_J wrote: Hi,I use an arducopter 2.8 and want to use a switch for arming instead of rudder right.I can't find anything on ardupilot.org and many other places, so I thought it would be best to...
View ArticleSimulated drone with pixhawk only
@somebody55 wrote: Hello, I have to create a simulated drone based on the ardupilot architecture using as an hardware only the pixhawk : all the devices that are supposed to be connected on the...
View ArticleClik here to view.
Copter seems to power failure then recovers imeadiately
@Nathaniel_McMahon wrote: Hi all, I'm looking for a little analysis help in finding out why my Quadcopter seemed to loose power fall upside down then regain power a second or two later. It seems from...
View ArticleApm planner can't resolve log file that added new field data
@liang-tang wrote: 44 struct PACKED log_GPS { 45 LOG_PACKET_HEADER; 46 uint64_t time_us; 47 uint8_t status; 48 uint32_t gps_week_ms; 49 uint16_t gps_week; 50 uint8_t num_sats; 51 uint16_t hdop; 52...
View ArticlePixhawk bad logging error
@Shailoy wrote: HiI have recently bought pixhawk and installed new firmware 3.5.6 for my Quadcopter. I am getting bad logging error on arming.can anyone help me with this Posts: 1 Participants: 1 Read...
View ArticleClik here to view.
RaspberryPi3 and APM2.6 via MAVProxy
@kungfrank wrote: Hi everyone, I'm newbie here.I am following this guide: http://ardupilot.org/dev/docs/raspberry-pi-via-mavlink.html i know Rpi3 has changed the uart access,following reply form...
View ArticleUser action log in MP
@Sagaris wrote: Hi all! Does Mission Planer log user's actions or outbound MAVlink messages? How one can analyze user activity during flight? Regards. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Great UAS Research using Ardupilot presented at AHS International Forum
@bnsgeyer wrote: AHSInternational.jpg943x300 89.9 KB AHS Internatiional is a professional vertical flight technical society. Much of the presented research was devoted manned vertical flight. This...
View ArticleMission planner not working in 3.5rc05
@X1Aero wrote: There's already a post on this over at Mission Planner, but after some testing this problem only exists on 3.5rc05. I have two units using a Pixhawk 2.1, one running 3.5rc04 and the...
View ArticleToday, My Quad Copter ascend while RTL and Land? (Copter V3.4.6)
@dongfang_a wrote: First of all, it has no relationship to RTL_ALT. In most time, RTL and Land modes always work fine for me. But today, when I switched mode from Loiter to RTL (throttle was middle...
View ArticleRequest to do auto tune in loiter? mode
@dongfang_a wrote: I'm not sure whether it is too complicate to do that, just I have to chase my drone during the auto tune process, and some time I have to break auto tune process too many times. If...
View ArticleFeature to auto-reset airspeed to 0 when armed? Or should ARSPD_SKIP_CAL...
@marcmerlin wrote: Hi @WickedShell and @Graham_Dyer, thanks for your help at the time in...
View ArticleFollow heading instead of waypoint?
@iter wrote: I'm working on an autonomous sailboat. I'm in the process of selecting hardware now. I'm curious if there is a way in ArduPilot to tell the vehicle to follow a particular heading rather...
View Article