Ac 3.5 landing gear behavior
@kuspower wrote: Hello, for thos uses landing gear controller, there's an issue due to PWM output during pixhawk startup that make thoses controller unusable. for exampleIf LGR_SERVO_RTRACT set to...
View ArticleArducopter APM 2.8
@espooblue wrote: Hi, I am new to this, i finished building my quadcopter, using api planner 2.Have been trying to configure it to fly using the X type, but i am having constant problems.Copter just...
View ArticleTarot 680 Iron-man unstable
@DARKHOURS wrote: I have the Tarot 680 iron man with PixHawk4 Qx-motor QM4208 380kv running 15x5.5 t motor props. the problem I am having is when I try to take off and get about a foot off the ground...
View ArticlePopWing flying wing - Cruise mode issues
@Jan_Hindoy wrote: Controller: MicroPix with FW V3.7.1 (22b5c415)GPS: Ublox NEO M8NRadio: Taranis Plus TX with D4R-II receiver. I have been tuning and tested the wing for some time now, and it is...
View ArticleAbout Power Consumption
@111116 wrote: I want to know Pixhawk and APM 2.6's power consumtion(W). Posts: 1 Participants: 1 Read full topic
View ArticleFlaps and Ailerons in Arduplane
@Rusty_Jones wrote: Flaps and Ailerons in Arduplane This probably applies to all recent versions of Arduplane, so hopefully someone can clear things up a little for me. I am installing a Pixhawk in a...
View ArticleRaspberry pi connecting to PX4 via mavlink (Dronekit-python)
@tkdronnie wrote: Hello,I am tying to callback the mavlink common messages from pixhawk using raspberry pi 2 model B. I am using dronekit-python and a decorator to call the...
View ArticleAltitude follows desired altitude then begins oscillating
@violas15 wrote: Hello,I am working on flying an iris+ quadrotor indoors without GPS using an onboard computer to send attitude messages. The positioning is working well however the altitude of the...
View ArticleHERE + Firmware Problem, U-blox software not finding COM port once driver...
@dronesurvey wrote: Hi everyone. I have been trying to update the firmware for the HERE + using the protocol described in:...
View ArticleTime has wrapped error
@pziyang wrote: HI all, When connect mavproxy to pixhawk (running px4 firmware), i keep getting error 'Time has wrapped, xxxx, xxxx' This is spamming the mavproxy commandline. Does anybody know what...
View ArticleMissing initial photos when starting a new strip
@Joao_Marques wrote: Hi! Why is flight controller not taking the initial photos (between 1 to 3) every single time the drone starts a new strip but it continuous to take photos in the end? Take a look...
View ArticleMission feature is affected once geofence is enabled
@surya2807 wrote: Hello All, I am working on a Linux System. I had setup the SITL environment and started testing the features one by one. The Mission feature by giving way points runs perfectly...
View ArticleUblox press release featuring Ardupilot and Here+ RTK GPS
@OlivierB wrote: Nice press release from premier Swiss based GPS manufacturer ublox, promoting Ardupilot, HEX Taiwan, and the Here+ RTK solution. Designed by ProfiCNC and Ardupilot development team...
View ArticleDual Sonar setup for left and right turns - MB1240
@bhollehday wrote: The old pixhawk had a 5 pin ADC port with two separate pins for reading the output signal from the sonar. The new pixhawk 2 only has a 3 pin ADC port with one pin for sonar signal....
View ArticleProblem with Loiter Mode with PX4Flow
@Ivan_Lee wrote: Hi, I have been flying my Pixhawk drone and trying to get optical flow position hold working. Following the Ardupilot instructions here...
View ArticleHelp pixhawk & gps
@Carlos_FPV wrote: Hi, I have some issues with my Pixhawk and I need your help!1 - It is supposed that the gps contains a compass for orientation that is the one usually is used in flight apart from...
View ArticleFailsafe Issue: My ESC shuts off Completely, not what I want, help
@jwcalvert wrote: I am building a Plane Drone with a Pixhawk, Taranis Plus Radio and X8R Receiver. Everything is setup through Mission Planner and it all seems to work including GPS, GCS link, radios,...
View ArticlePixhawk and ESC EMAX NANO 12A OneShot125 problem
@tomekr wrote: Hi AllI need help and adviceI build small quad with pixhawk ( firmware 3.4.6) and ESC EMAX NANO 12A OneShot125.First I have a problem with calibration. I do step by step (...
View ArticlePixhawk 2.1 HERE GPS Altitude Incorrect
@ChiefG wrote: Hello,I'm currently using the non RTK version GPS, just HERE GPS with a Pixhawk 2.1 and seeing my altitude at 240+meters. Is there a way to fix this? Is this normal? Thanks,Ben Posts: 3...
View ArticleIs this possible to try precision Landing with Optical Flow?
@walkeryu123 wrote: I can use the precision landing with GPS, Is it possible to use the precision landing at indoor environment with optical flow or other sensor? Posts: 2 Participants: 2 Read full...
View Article