Console terminal and SBUS output pins of PH2
@Sunit_Pal wrote: In PH2 the 6 pins next to the power connectors are for Console and SBUS. However it has not been labeled as to which pin is what. I cannot find this information in the 2 pdf files...
View ArticleWhere to update_position() func
@hiroyuki405 wrote: Where to update_position() function?I m locking for update_position() but I can't foundWikipedia explained that update_position () func exists in AC_PosControl.cpp...
View ArticleClik here to view.
The limit length between Pixhawk and Teraranger?
@Kyomo_Jung wrote: As below log analysis, when Arducopter(3.4.6) raised up over about 2m Teraranger is death. I was afraid the cable length ( about 50cm ) between Pixahwk and Teraranger was causing...
View ArticleClik here to view.
Problems get the ArduPilot repository (submodule)
@MiSta wrote: Hello, I have problems cloning the ArduPilot repository.(Using Ubuntu 16.04, git-version 2.7.4) "git clone .." works fine. But "git submodule update.." results to "fatal: unable to...
View ArticleROI Effect within Circle Mode?
@pmshop wrote: Is there an "ROI Effect" when using Circle Mode?When I started to lower my craft while circling, the nose became fixed where the craft started to descend. More info...
View ArticleUsing a HERE+ GPS on a Pixhawk 1 with Arduplane
@Rusty_Jones wrote: So this is probably 2 questions: 1) Will a HERE+ GPS work on a Pixhawk 1? ( I think it will) 2) Can Arduplane 3.7 use the HERE+ GPS? Thanks ! Posts: 6 Participants: 2 Read full topic
View ArticleClik here to view.
Compass Offsets HIGH // external + internal compass in use
@Alex77 wrote: Dear community, i use ArduCopter V3.4.6 on a 5kg Hexa-Copter and did a couple of test flights after compass calibration on a wide farming field with no obvious disturbing items around....
View Article(Rare?) pre-arm failure: GPS 1 failing configuration checks
@flightzoomer wrote: Hi, While setting up my first Arduplane aircraft, I am encountering the following pre-arm failure: Pre-arm Message:PreArm: GPS 1 failing configuration checks Followed by:GPS 1:...
View ArticleAltitude Angel login option not present
@yyyh412 wrote: Did this feature go away?, I can no longer right-click and log into my AA account. The option is not present. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
SR# params changing
@X1Aero wrote: Been autotuning and comparing my full param list to choose the best AT and notice my SR0 and SR1 params have all changed. Any reason the the autopilot would change the stream rate?...
View ArticleClik here to view.
UnauthorizedAccessException when trying to download firmware V3.4.6
@UIResearch wrote: Here's the screenshot of the error I'm getting upon trying to install firmware under MP Initial Setup: Screenshot.png944x708 679 KB It's worth mentioning that I can connect to my...
View ArticleIs my Pixhawk dead?
@Leslie_Chan wrote: Hi All, I'm assembling new Hexa F550 when testing I had a few plug and unplug the battery. The last time I plug in the battery, I heard two beep then no more beep from the buzzer...
View ArticleChanging gyro and accel filters
@sakirpolay wrote: hello folks, i want to change my gyro (INS_GYRO_FILTER) and accel (INS_ACCEL_FILTER) filters from 30Hz to 40Hz maybe more . I want to ask what will be the positive or negative...
View ArticleApp Sync Download Logs not worknig
@Mad_angler1 wrote: Hi, I have just tried the App sync download logs app and its giving the following error Unable to locate /Home/User/DFlogs folder any suggestions, Im using latest Apsync image with...
View ArticleUsing Antenna Tracker with Mavproxy
@pziyang wrote: Hi, My setup is as follows: I have a pixhawk running PX4 firmware on my drone.There is another pixhawk running ardupilot antenna tracker I wish to setup the telemetry as follows drone...
View ArticleAuto-Land: The autopilot did not shut down the throttle when the plane...
@Captain wrote: HI, We are using a fixed wings plane with the Pixhawk1, airspeed and the arduplane 3.7.1 We were doing auto landing. we did 2 flights. The auto landing was not easy and we did multiple...
View ArticleInstant flip on version 3.4.6 and 3.3.3
@Chad_Frazer wrote: The airframe is a DJI S1000+FW for first flip: 3.4.6 then downgraded to FW 3.3.3, then it flipped in same manner and same direction again 4 files provided here.2 Parameter file...
View ArticleTelemetry link but no data Mp can't no connect
@jhpantaleon wrote: Hi Any body know about this I am new and I have to telemetry and de same problem I have a problem with a FPV Radio Telemetry, I connected it to my APM 2.8 and USB ground to my PC....
View ArticleSolo Cube vs Pixhawk Cube
@re4mat0r wrote: Hi. What is the difference between these two? I mean Cubes which were in Solo, with black plastic enclosures and new metal Pixhawk 2 Cubes. Thanks,Roman Posts: 1 Participants: 1 Read...
View ArticleQuad Crashes after thrusting vertically up
@Moshe wrote: Greetings everyone, I have a double problem, I have just finished a quad, with Pixhawk flight controller and Turnigy motors 4240 -750 and turnigy esc, I did all the configurations and...
View Article