DLVR for Wind Library Developement
Topic: DLVR for Wind Libary Development Proposal type: Hardware , Software , Other : _________________ Description: I would like a Matek DLVR sensor for benchmarking new wind sensor drivers that...
View ArticleUnable to connect to Mission Planner and X-Plane
I am having a problem connecting my configured ardupilot sitl with mission planner and x-plane 11. I followed the instructions on Using SITL with X-Plane 10/11 — Dev documentation. I tried all the...
View ArticleClik here to view.
Drone keeps Yaw spinning at takeoff
Hey guys, im working on a first build and the drone keeps spinning during takeoff. I have these raw servo output logs and i can tell there is a massive difference between serco 1 and 3 and 2 and 4 if...
View ArticleHuman tracking guidance using pymavlink - Delay problem between attitude and...
Hi, We want to guide drone using camera feed to track a human. We use pymavlink libraries to get drone attitude and send guidance commands as follows. In the below commands, “guiCmd” struct is...
View ArticleWhy magfit's output result is out of parameter range?
I have met a compass issue here And magfit gave a result out of parameter range, is there any way to configure to do a re-calculation? As I can’t simply apply those out of range parameters to copter....
View ArticleGimbal SimpleBGC Setup
Hello. I have a problem - my gimbal om SBGC working strange - gimabal come back to 0 position in mavlink tar and rc tar mode. i know about parametr MNT1_RC_override, but if they have value >0...
View ArticleConfigering a Maytek F405-TE for a plane
I am somewhat a basic user of computers but currently trying to set up a flight coach controller for a F3A plane. I have purchased a Maytek F405-TE and attempted to create the appropriate firmware,...
View ArticleDrone CAN required for battery monitoring?
Hi, I am trying to set up my DS500 drone with a Tattu 10000 mA/h battery. I need to monitor and alter battery performance via a Matlab model. This is to produce a digital twin of the drone. Can you...
View ArticleWhere is MP source code? Want to do Interface design
Hello, dear forum users. I apologize if a similar question has already been asked. Please tell me where in the MissionPlanner source code the interface files are located, I want to modify it a little,...
View ArticleSpeedyBee F405 40A AIO 1-6S
Does the SpeedyBee F405 40A AIO 1-6S support ardupilot firmware like F405 V3/V4 or mini 2 posts - 2 participants Read full topic
View ArticleMAVLINK on additional serial port for BT communications
(topic deleted by author) 1 post - 1 participant Read full topic
View ArticleGeotag images taken by Siyi gimbal/cameras
This question may be particular interest to @rmackay9 and @SIYI A question came up recently about the ability of SIYI gimbal cameras to geotag images in the image EXIF when they are taken. As far as I...
View ArticleHas Anyone Tried the SIYI A8 mini camera?
I have been searching for a camera/gimbal setup to replace the Tarot 3 axis/GoPro Hero 4 combination I have on my quad. I cannot calibrate the gimbal because the software runs on XP machines, and I...
View ArticleThe q ground controller not getting connected to pichawk cube black with the...
I am trying to connect QGC inbuilt app on the mk 15 trx with the mk air unit but its not working I changed SERIAL1_baud to 56700 I tried changing the SERIAL1_PROTOCOL to 1 Did same for serial 2 also...
View ArticleDrone disarmed during flight in mid air after 3 to 4 min
i am using pixhawk 2.4.8 with respberry pi 5 through serial communicationn with tlemetery port 1. i have done calibration through ardupilot and using pymavlink library for control during flight all...
View ArticleMixing two SerialProtocol_XXX on one serial port
# USART1 # for PPM PA10 TIM1_CH3 TIM1 RCININT PULLDOWN #for Telemetry PA9 USART1_TX USART1 define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_FrSky_D Will it work? Could be SerialProtocol_FrSky_D uses...
View ArticleClik here to view.
RC Override Command in Python is not working
Would like to ask if the rc override command not working? Because my vehicle is not getting the RC override. I was able to read the RC from a channel when the input is from the controller but when I...
View ArticleMost Popular Open-Source Gimbal for ArduPilot in 2025
Hi Almighty community members I’m looking a gimbal hardware using open-souce code, which is integrated in ardupilot (Prove to be work, good performance/ affordable price. How about SToRM32 NT gimbal?...
View ArticleUnable to Arm Quadcopter in Loiter Mode
Hi I am using Pixhawk Cube Orange+ for RTK Drone setup by using ArduSimple RTK F9P GPS module for GPS and Here3+ for compass and for base station ArduSimple RTK F9P . So I Unable to arm quadcopter in...
View ArticleClik here to view.
Linking Error into SecureBootloader
I am working with CubeOrangePlus. I am working on the Secure Bootloader process given on: ardupilot/Tools/scripts/signing/README.md at master · ArduPilot/ardupilot · GitHub I follow the steps as given...
View Article