Quantcast
Channel: ArduPilot Discourse - Latest topics
Browsing all 45666 articles
Browse latest View live

Crash on first flight after mayor crash

@cvaldi wrote: Hi,I had a very bad crash a while ago. I had to replace almost all the frame so I bought a new one, including motors and esc, the frame is a DJI S1000+. On the first flight with new...

View Article


Only Acro mode available

@Maximich123 wrote: Hi everyone!There should be an easy answer, but I have struggled to find it for several days. The problem is, that after several successful flight in a row in different modes...

View Article


Is it safe to use a Servo port in order to create a 3.3V tension?

@Hameck wrote: I need to turn on a LED during the flight, is it safe to use PWM signal in order to obtain 3.3V? Posts: 1 Participants: 1 Read full topic

View Article

Trouble uploading 3.4beta?

@X1Aero wrote: Keep getting failed to download when installing 3.4 beta in mission planner. Anyone else having trouble? Tried three different computers. Posts: 2 Participants: 2 Read full topic

View Article

Trouble firmware download

@X1Aero wrote: When trying to update firmware (arducopter 3.3 or 3.4) I get failed to upload... Tried three computers and all with the latest Mission Planner. Anyone else having issues? Posts: 6...

View Article


Diable the "stop" in stabilize

@qemay wrote: As I have some more time I decided to finish my pixracer (3.4 rc1) 250 class copter. It need's some tuning as it wobbles during flight. - But that's not the point of the question. In...

View Article

Mission Planner 1.3.38: Moving base question

@henrik04 wrote: Once [Moving base] is started and update the little "home" icon on the flight data screen:- Will RTL return to launch or to "home" position? Thank you. Posts: 1 Participants: 1 Read...

View Article

Image may be NSFW.
Clik here to view.

Sudden CTUN.ALT altitude change during takeoff in AltHold

@ivereninov wrote: Hello! We are actively testing 3.4RC1 with Navio2 and have noticed a potential issue. In this flight we took off right after reboot in AltHold until GPS had a good fix, you can see...

View Article


In MP 1.3.38.1, Rate Roll/Pitch D limited to 0.024

@lorbass wrote: In the MP Config/Extended config the Rate Roll/Pitch Value D can't be increased higher than0.024 manually. With this value on CH6 it's possible to set it higher. But afterwards not set...

View Article


Additional Mavlink output on Serial4 for OSD?

@dk7xe.g wrote: I'm running AC3.3.1 on all of my copters and installed on 2 of them a micro-minimOSD.Since i was loo lacy to build a Y cable for Telemetry TX and OSD i connected the OSD to serial 4...

View Article

Throttle percentage in HUD?

@dksmall wrote: I'm trying to get my rover tuned up and one of the steps is to set cruise_throttle to your throttle percentage when the rover is going at a speed equal to your cruise_speed. I don't...

View Article

Crash Could use some assistance

@rickyg32 wrote: I have a friend. Yes its a friend not me that has a small quad that while in loiter appears to suddenly power down and the first few times resulted in a crash. Today he attempted...

View Article

Arduboat Kayak Spins in circles

@art62 wrote: Hello everyone, I recently built a arduboat kayak for lake mapping but I have an issue. When I set Auto mode with waypoints the kayak just spins in circles , moves , and spins in circles...

View Article


Descent stops at 50m

@timvand wrote: Ok, dumbass question. Ran autotune on a rig, and completed without any issue. Next, planned a 6 min map mission with 4 legs, at 100m Alt. Mission runs and returns to home point, rig...

View Article

Elevator direction in Radio Calibration section

@Paul-H wrote: Hi all A quick question I hope When using Arduplane the Elevator direction in Radio Calibration has to be reversed ie pull the stick back and the activity bar moves up. Is that the same...

View Article


APM 2.5 latest possible Airplane SW

@toto44 wrote: Hello,I reactivated my APM 2.5 or 2.6, I am not sure. Now I want to use the correct Firmware for my plane. I read that Arducopter 3.2.1 is the latest possible Firmware for APM2.x for...

View Article

Quadplane Transition Done (and then issues with second attempt!)

@jacques_eloff wrote: I did some transition flights today – the first went down perfectly well. However on the second, something strange happened: Once transition was achieved (in FBWA mode) I started...

View Article


Advice on Trim [porpoising] not related to PIDs, FLYING wing setup

@raptor wrote: I have a flying wing and while there probably is a small issue with structural flexing between the fuselage and the high aspect ratio sweep wings looking at the log I wonder if there is...

View Article

Still need to set COMPASS2_USE to 0 to be able to ARM :(

@marcmerlin wrote: I have a pixhawk and a pixfalcon in 2 different airframes.Neither will arm because of "compass inconsistent".I think this started in 3.5, but not sure anymore. I've just had to...

View Article

Simple question about overlapping waypoints and rover path on tlog

@Roverman wrote: When a mission is actually happening, yellow lines and circles show where waypoints are and a purple line is left behind the rover to show where it has gone. However, whenever I open...

View Article
Browsing all 45666 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>