Correcting a 'wobbly' path between Waypoints?
@John_Easton wrote: A wobbly path wastes time and fuel when carrying out a survey on a large body of water. Not to mention the safety hazard should there be another boat on the water and the skipper...
View ArticleStorm 32 controller calibration
@brus wrote: HelloI am having problems calibrating the imu2 and camera imu on a storm 32 controller. In the OlliW BGC tool, when calibrating,,,values stabilise ,, the blue arrow doesnt appear and the...
View ArticleUsing 2 servos for pitch
@Nikita wrote: Hello, I want to use 2 servos for pitch in APM 2.6, they should spin in opposite direction. How I can change spin direction of 1 servo, since they are both connected to 1 RC output? The...
View ArticleIs it possible to compile ArduCopter 3.3.3?
@R_Q_Robert wrote: Hi All I have successfully cloned [and compiled] the latest ArduCopter code [AC3.4-dev] for Pixhawk by git clone https://github.com/ArduPilot/ardupilot.git But now i am unable to...
View ArticleHome location could not update
@cookmangr wrote: Hello i have 2 problems I have 14 sats and hdop 0.6 at my pixhawk and firmware 3.3,3 and mission planner shows this messageHome location could not update I cant see how much far away...
View ArticleCurrent draw makes 0.5A steps
@paan2097 wrote: When running ArduPlane 3.6 in a MAVProxy SITL instance, the current draw does something wrong. The voltage stays pretty constant, usually stays around 12.587 but can change to 12.537....
View ArticleMP v1.3.39 - can't find beta updates/version
@MFlight wrote: I'm trying to get beta updates/versions after 1.3.39 1.1.6038.12291 with no luck. After going to help>check_for_beta_updates the update window pops up, eventually updater.exe runs,...
View ArticleCopter enters FAILSAFE_BATT-1 mode with allmost full battery
@Philip_de_Lang wrote: I am new at building copters, built 2 sofar, the last one is a Tarot fy680 with 6 Quanum MT Series 4108 475KV motors and a multistar 10000 mah 10c lipo and a Storm32 3d gimbal....
View ArticleCopter flipped over when taking off in Stabilize Mode
@iseries wrote: Using 3.4.2-RC3 after doing an Auto Tune for Yaw and landed, taking off in Stabilized caused copter to flip over the first time I tried to take off. The logs show at 125 that the...
View Article3.4rc3 mission Chute params?
@X1Aero wrote: These are no longer in the full params list: CHUTE_TYPE = “10” to release with a servoCHUTE_SERVO_ON should be set to the servo position required to release the parachuteCHUTE_SERVO_OFF...
View ArticleRover has lost its mind on day 2
@dksmall wrote: I'm preparing my PixHawk based rover for AVC. I can set waypoints and drive a course with good repeatability. I power off the rover and go home. I go back to the same location the next...
View ArticleOneshot125 and rc3 still strange
@cala2 wrote: I activate again oneshot 125 (type2) , I try two times, the secuence tones looks working but them, when I connect batt, two motors beep, after push button, then the other two motors...
View ArticleDownload ArduCopter master and Cannot Control
@jane wrote: I download the branch "master" from the github and compile it, why does the UAV couldn't be controlled? Posts: 2 Participants: 2 Read full topic
View ArticleWaypoint Missions
@infusion123 wrote: Hi , its my first time here so I'm not sure what are the posting ethics here , sorry if I posted in the wrong forum.So my issue is , I followed the instructions here...
View ArticleClik here to view.
Compas#2 calibration out of view
@vonfrank wrote: Hi there I am very new to ardupilot, and a new user on this forum. Hope someone can help me, with my problem. I am running arducopter 3.3.3 on my DJI F550 hexacopter. When i try to...
View ArticleClik here to view.
Magnetometer Calibration Issue
@thorphar wrote: I've just got myself a APM 2.8 along with a uBlox M8N GPS (with compass) module. During the configuration process of the setup for the APM I came across this issue....
View ArticleSTB_PIT_P / RLL_P value 0
@gfun wrote: You can see in video, as soon i press refresh button, all values goes to 0. I tried to flash it again, tried load defoult settings . did not helped. Any options ? Posts: 6 Participants: 3...
View ArticleMission Planner Incorrect Battery monitor voltage
@alpa2009 wrote: Hi,trying to manually correct the voltage monitored by mission planner:According to http://ardupilot.org/copter/docs/common-power-module-configuration-in-mission-planner.html you can...
View ArticleClik here to view.
AMP 2.8 For what this?
@gfun wrote: apm_3.jpg820x595 99.2 KB this small thing( resistor?) is for what? On another board i dont have it Posts: 1 Participants: 1 Read full topic
View ArticleEmax 4in1 25Ax4 and Pixhawk
@tomekr wrote: Hello AllI'am a begginer Anyone can help me with max 4in1 and pixhawk.In emax I have six wires four white one red and one black. Any idea how it i should connect with pixhawk ?...
View Article