SoloLink w/ Pixhawk Cube for Rover?
@RobotWerks wrote: I have been searching everywhere for info on using the Sololink IMX6 board from the 3DR Solo with the Pixhawk Black Cube and cannot find much of anything. I am hoping to use...
View ArticleGuided for autonomous quad copter
@aliebrmy wrote: i want to make up an indoor autonomous quad copter(without GPS) and i have Pixhawk 2.1,raspberry pi 3 and Px4flow i need some tutorial about this way. i search almost everywhere and...
View ArticleClik here to view.
Something is wrong with my copter build
@mtnsurveyor wrote: 00000007.BIN (477.6 KB) I have made a mistake here and I am not sure how to fix it. I followed the tuning wiki and it did not help this situation. The copter is a 500, 6s with...
View ArticleFrsky s.port telemetry on kakute f7
@Tilen_Kelc wrote: I was wondering if there is a way to use s.port from x4r on kakute f7 aio. I tried to use uart 4 and set it up for frsky s.port, didnt work then i read that it has to be on uart 6,...
View ArticleClik here to view.
Question about gear requirements
@Stanley_C wrote: With this equipment + standard RC plane equipment(transmitter, receiver, esc, servo, motors), would this be enough for waypoint missions using GPS+ compass? amazon.com Amazon.com:...
View ArticleMatek f405 CTR wiring issues
@woogie_man wrote: Hey guys… .I am sorry to be “that guy” starting a thread and asking for help. I was using another system and had a few crashes that were due to software issues, and I was wanting to...
View ArticleWhat should I do to output Custom PWM from AUX1~6
@CChen wrote: It is useless to write like this in Arducopter.cpp，The output of the oscilloscope is 0： hal.rcout->enable_ch(13); hal.rcout->write(13, 1500); Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Arducopter geofence breach throws random breaches
@Naveen_Raj wrote: the geofence breach and fence breach mechanism does not work properly and keep showing random outputs of breach even when the copter is inside geofence and if the copter is outside...
View ArticlePX4 firmware upgrade with MP and QGC impossible
@bpoxman wrote: I have a Radiolink Mini Pix V1.0 , installed from factory with the firmware Arducopter 3.5.3 , and I wish to upgrade it to the lastest official version 3.6.10 (which give me all...
View ArticleBlheli_32 will not connect to pixhawk1
@Hquarter wrote: I have been working on upgrading my esc’s from older simon k Muti-Pal esc’s to Iflight SucceX 60A Plus BLHeli32 ESC. Everything has been wired, I have studied the wicki, and what...
View ArticleSplit one input into two servo's (functions)
@ON7AMI wrote: Hello, New to the whole project I’m very exited of it. Before I read all the documentation I had a question: is it possible (without intervention in the software) to split the input of...
View ArticleProblem installing Firmware Copter 3.6 on ArduCopter APM 2.8
@Adrien_Kirschner wrote: Hello, I am a student currently doing my Bachelor Thesis, and I have to build a drone. Unfortunately, I can’t install the Firmware Copter 3.6 on my ArduCopter 2.8 Flight...
View ArticleKayak Assist for the Blind
@Rupert_Powell wrote: I am looking into the feasibility of an assistive device for a blind kayaker, They would like to set way-points down a river and receive instruction (sound/voice/haptic) to help...
View ArticleHP Printer Not Activated Error Code 30
@carryjhn wrote: There are so many printers in the market but HP is one of the best printer and scanner provider so far HP Printer Not Activated Error Code 30 solve all the error which generated...
View ArticleClik here to view.
VTOL exceeding groundspeed limit
@jace26 wrote: The other day I was bringing a VTOL plane ( with 3.9.9 stable) back to its take-off location from some distance away in QLoiter, when I noticed visually that it seemed to be traveling...
View ArticleClik here to view.
Cannot download log via mavlink
@Alec wrote: Hello everybody, I am currently trying to download my flight log so I can improve my drones flight characteristics and analyze its flight. Whenever I attempt to download my logs i get the...
View ArticleNew to Arducopter
@rjriggins111 wrote: I’m new here and have a question for someone with more experience than me. I have a 2.8 version APM flight controller and need to know which version of mission planner it will...
View ArticleDual Rangefinders priority
@autopiloton wrote: When using dual rangefinders for terrain following auto WP missions how does the flight controller prioritize them? i.e. is RFND1 used as the primary source of distance and RFND2...
View ArticlePlease help me Pixhawk hexacopter unstable problem
@dkshin wrote: I want to ask two questions. I set the hexacopter 1500 size drone as the latest arducopter. We changed the PID value under three conditions. Changed PID settings for the Hexacopter 1500...
View ArticlePID stting error
@dkshin wrote: I have a PID setting of 1500 hexacopter drones. After setting the PID value obtained through autotune, the drone is stable. Afterwards, I recalibrate the sensor and re-enter the PID...
View Article