Holybrox 4 mini repeated crash after 4.0.0 loaded
@Gavin wrote: Very new to the hobby. First time building a drone, I built a Hex running a pixhawk4 mini. Last year I was unable to configure the mini with arducopter. One verson didnt recognise the...
View ArticleKakute F7 AIO and Pinout described on Hardware page
@RizHass wrote: I am interested in building a QuadCopter using Kakute F7 FC, but I will be using the Mission Planner (Ardupilot) firmware and GUI interface (Ardupilot supports F7). On Ardupilot...
View ArticleUAVCAN ESC 0 not working
@gnitzan wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleTrouble with Ground Control Installation on Ubuntu 16.04
@Lion_AUV wrote: Hello! I’m just a beginner to autonomous vehicles and trying to install QGC on my Linux machine. I successfully installed QGC on my Mac last night, but when I was attempting with...
View ArticleArduplane 4.0 on Pixracer
@User_4 wrote: I am using an mrobotics pixracer R14: https://store.mrobotics.io/mRo-PixRacer-R14-Official-p/auav-pxrcr-r14-mr.htm On Arduplane 3.9 in Mission Planner, I can see that the channel...
View ArticleMOXON Antenna for 915 Mhz
@charles_linquist wrote: I have designed and built a 3D-Printable MOXON antenna for 915Mhz. it is fairly directional, but is small (120X50mm) and has significantly better performance than a 1/2 wave...
View ArticleIncomplete AutoTune Copter 4.0
@K_Trlicek wrote: After upgrading from 3.6.10 and 3.6.12, I wanted a tighter tune using Copter 4.0. I’m using the RoboCat 250 mm frame, Solo 3DR Cube 2.0 w/Mini Carrier hard mounted, DYS 2204 2400kv...
View ArticleClik here to view.
Does QGC upload TERRAIN_DATA to the vehicle like Mission Planner?
@Pogo wrote: Does QGC upload TERRAIN_DATA messages to the vehicle like Mission Planner? I’m using ArduPlane SITL with X-Plane 11 and QGC doesn’t seem to…? Thanks Posts: 1 Participants: 1 Read full topic
View ArticleFS: Pixhawk1 (FMUV2) Bundle
@Saijin_Naib wrote: I have a seemingly complete Pixhawk1 FMUV2 setup with SiK radios, power board, etc. that I am not using. Would anyone be interested in it all? Posts: 1 Participants: 1 Read full...
View ArticleConnecting multiple custom telemetry data in mission planner with custom screen
@tikawawa wrote: Hi, I am using the pixhawk on 2 IC engines and I need to see a lot of data in mission planner like, 8 x thermocouple temperatures and 2 x rpm signals. I looked through the...
View ArticleWrong consumed mah
@Corrado_Steri wrote: I recently changed my distribution board and installed a spektreworx kore. Everything works as expected except for the consumed mah. I set the correct battery monitor data as in...
View ArticleSecond IMU error when arming Pixhawk 2.4.8 copter 4.0.1
@MarcK wrote: 1 1970-01-01 01-00-00.zip (601.2 KB) Hi. After installing on pixhawk 2.4.8 copera 4.0.1 version for fmuv3 and then pixhawk 1 in 9 cases after turning on the power, the second...
View ArticleLocal_position_ned message not streaming\not received
@danielh wrote: Hi, I am trying to receive LOCAL_POSITION_NED messages. I am using optical flow (loiter mode works great, so I know the optical flow is functioning), however I am not receiving...
View ArticleChiBios OSD Distance from Home Set from Feet to Miles
@Alexander_Perez wrote: Hello. I’m using ArduPlane V4.1 firmware and mission planner 1.3.70. All works great. One question I have is how to change the “distance from home” units from feet to miles on...
View ArticlecliSerial->printf now printing hordes of binary info
@jwcalvert wrote: I just recompiled my rover with 4.0.1 and cliSerial is printing a lot of unwanted binary with my intended output. A good search shows no other printf commands other than my own. Is...
View ArticleMission Planner won't connect to Pixhawk when SBUS Receiver is connected
@AZ_Ron wrote: Hi all!! I’m hoping someone can steer me in the right direction. I’m refurbing a 700mm Quad as a Long Distance landscape/nature photo platform. I’m attempting to connect my TBS...
View ArticleClik here to view.
Camera Gimbal - Can't control via RCIn
@itsyoshio wrote: Greetings, I’ve been trying to get my Feiyu MiNi 3D Pro working in conjunction with ArduCopter. This Gimbal has 3 PWM Pins for Tilt, Pan and Mode switch, aswell as a Ground. It’s...
View ArticleClik here to view.
Running two or more versions of mission planner on same computer
@m_j1 wrote: a practical question has just immerged I have a s500 quad running the great apm2.8 actually it was the first quad I ever built, still impressive though aged 5 years. I decided to build a...
View ArticleClik here to view.
Unstable Alt Hold
@ardisd wrote: I have been have a problem with Alt Hold / Loiter height being unstable. When switched to ALT Hold and Loiter The copter will bounce up and down very sharply. This dosn’t happen in...
View ArticleMIssion Planner Log Analysis-filter by flight mode
@nagordon wrote: Anyone have any luck plotting time series values filtered by flight mode. For example, I would like to only plot Mode FBWB with ATT.Pitch. Thanks Posts: 1 Participants: 1 Read full...
View Article