Impossible to upload the new geofence in copter 4.0.1 in holybro pixhawk 4
@Gourav1997 wrote: The geofence is not uploading in copter 4.0.1. It shows " This vehicle does not support geofence" in QGroundControl and in Mission Planner the marking and uploading of polygon is...
View ArticleBenewake FT-Mini Plus not working after I2C address change
@Bram_Dons wrote: ls After changing the I2C address from 10hex to 11hex with the SSCOM program (obtained from Benewake support) Ardupilot could not recognize the TF-Mini Plus anymore. Posts: 1...
View ArticleClik here to view.
Urgent: S.BUS input on 4.0.1 is stuttering often 100-300ms, up to 500ms
@VDLJu wrote: Hi, After using 4.0.1 for few flights, I observed that it feels like there is lag on RC input. One time I just ARMED the drone and it got the RCIN failsafe and it DISARMED immediately...
View Article24GHZ millimeter obstacle radar not working in automode
@kalai1219 wrote: I have installed foxtech millimeter obstacle avoidance sensor. https://www.foxtechfpv.com/24ghz-millimeter-wave-obstacle-avoidance-radar.html It is working in loiter , althold but...
View ArticleClik here to view.
Wizard x220s not connect to FLYSKY fs-i6x
@roalroga wrote: Press the reset button and now the transmitter does not connect with me, what settings should I make on the drone and the transmitter. Screenshot at Jan 25 22-49-19 (1).png1439×684...
View ArticleAutoconnection via Radio Telemetry
@piamu wrote: Hello, we are trying to built a dronekit python code, that automatically bulids a connection to our drone and gives it a mission. We took the “Basic_Example”...
View ArticleNoob Question on Coax Copter
@rickyg32 wrote: Hey out there. I have kicked around the idea of a coax copter for a while and this past weekend started designing on…at least in my computer. When something struck me. I know how it...
View ArticleI wanna know about "optical flow"
@Moksh wrote: Hello , everyone, I wanna know about what is a optical flow , how it’s work properly and which is the best , can I made on raspberry pi ? , And can we made avoiding system using camera...
View ArticleClik here to view.
Kakute F7 and with Raspberry Pi as companion computer
@WeAreReady wrote: I’m thinking about using Kakute F7 for my next project. My idea is to install Ardupilot on it, connect a RPzero as companion computer and control the drone from a ground control...
View ArticleI want to mount my cube 2.1 upside down and the front at the back
@MartyMcFly wrote: Hi every one I want to mount my Cube 2.1 upside down and the front at the back,think it should be roll 180 and yaw 180 can not see A setting for this do I just have to do custom...
View ArticleSending commands via /mavros/setpoint_velocity/cmd_vel in guided mode
@elgarbe wrote: Hi, I’m trying to drive an hexacopter through mavros. My setup is Pixhawk 1 with arducopter 3.5, raspberry pi3 b+ with ubuntu, ros kinetic and mavros (an old version, I think). I...
View ArticleClik here to view.
Dev Call Jan 27, 2020 2300 UTC
@CraigElder wrote: Congratulations Tridge sUAS News - The Business of Drones – 27 Jan 20 Well done Tridge! - Medal of the Order of Australia - sUAS News - The... In our world, we know Dr Andrew...
View ArticleClik here to view.
Congratulations Tridge!
@CraigElder wrote: image.jpg696×391 77.4 KB sUAS News - The Business of Drones – 27 Jan 20 Well done Tridge! - Medal of the Order of Australia - sUAS News - The... In our world, we know Dr Andrew...
View ArticleIn what section in LOG can I find UAVCAN ESCs telemetry
@gnitzan wrote: Hello everyone, Just had a maiden flight with a new OCTA-QUAD build 850mm. 8 X 380kv motors 8 X 16x5.5 foldable props 8 X Kotleta20 ESC 2 X Li-Ion 12800 mah DIY 2Mauch 50am sensors AUW...
View Article4.0.1 Orange Cube EKF Failsafe and Erratic Altitude Hold on First Test Flight
@Droner wrote: Hi Everyone, Started flight testing an orange cube today on 4.0.1 with a small hex frame. Setup reportedly went okay. However the first flight was erratic. The copter flew alright in...
View ArticleESC Calibration issues
@Sealwithabowtie wrote: Hello I’m getting having some weird issues with the quad I just built. One of them being is that I can’t seem to get the ESC’s properly calibrated. I’ve followed instructions...
View ArticleESC recommendation for hubmotors
@OldRaven wrote: I have a set of hubmotors here normally used in a hoverboard. They are 350W and in the hoverboard operate on 36V I like to use these for a larger rover. Does anyone have...
View ArticleClik here to view.
Lidar TFmini+ operating problem
@jiji79 wrote: Hello, since the beginning of December I have a functioning problem with my TFmini + which, at the start no longer displayed distance values on Mission Planner and although a...
View ArticleClik here to view.
Quadplane bad navigation performances
@dcamatti wrote: Hello, we are experiencing problems in navigation tuning with Skywalker X8 based quadplane. The problem is the intolerable poor navigation performance especially referring to mapping...
View ArticlePlease help IN INDIA 31 Jan is last date to register your UAV's
@ANIL_CHOUDHARY wrote: INDIAN Government made regulations for UAVs registration and flight permission (no permission no fly) First we have to register our drone on digital sky government platform...
View Article