Clik here to view.
3D Printed VTOL in the works
@quadsours wrote: Heres my 3d Printed VTOL-fw I have most of the work finished but noticed the 9" props are not able to cut the mustard. I did get it air born but it not happy. 12244577-a1280×720 427...
View ArticleClik here to view.
Should i plan in Cooling? And if so, how?
@Holly918 wrote: Hello, i am planning my first USV for bathymetric surveys on lakes anywhere between 10 to 20ha at the moment and i think i figured everything out right now. However, since i do not...
View ArticleArdurover Wheel Encoders not recognized
@Highly wrote: I am setting up wheel encoders on my mower’s motors. I’ve installed CUI quadrature encoders programmed for 400PPR. The geartrain is 18:1 and so I’ve set PPR to 7200 to start. With power...
View ArticleVehicle missing on Flight Data tab, and now on Plan tab
@Rusty_Jones wrote: Ok, haven’t updated Mission Planned in a few months, but I just did the other day. Since this new update, 1.3.72, I do not see the vehicle in the “Data” tab, which used to be...
View ArticleClik here to view.
Trouble with Maxbotix i2c
@bdemers wrote: I’m trying to connect a Maxbotix 1242 I2CXL to Rover and I’m not having much luck, the values for rangefinder1 and sonarrange are always 0. I tested the sensor with an Arduino sketch...
View ArticleCan't set path and control sub in simulation(ardusub QGroundControl)
@YuryArnold wrote: Hello Ardu Community! I have to work width ardusub for submarin control, pixhawk 1 using. For the first, I try to run simulation for sub controlling. I build ArduSub as was writen...
View ArticleDisable GPS in GUIDED mode
@curiosityrover wrote: Hello, I’m trying to run a simple script for takeoff but since I don’t have a GPS unit, I get a ‘no 3D fix error’ when running on GUIDED mode (I can arm the motors in STABILIZE...
View ArticlePixhawk 2.4.8 setup with Corssfire Nano
@Guitarman1 wrote: Hi there guys. I have a Pixhawk 2.4.8 on my F450 flamewheel and I have always used Flysky on this one while using Frsky on my racing drone. I brought myself a TBS Crossfire Micro...
View ArticleBenewake TFmini not working on kakute F7 mini
@Ervin_Liao wrote: Hey guys, I setup my TFmini according the wiki, but sonarrange is still at 0. I have tried putting the TFmini wires on both the i2c ports and uart 4, and even swapped the wires when...
View ArticleCrush in guided flight: Radio Failsafe - Disarming
@movicut wrote: ArduCopter 4.0.3 on pixracer, hexa, managed with companion computer in GUIDED mode, rc reciver (X8R) disconnected and removed from the drone after successful autotune. Several times...
View ArticleRegarding plane
@quadsours wrote: Hello, I have a few questions after programming a VTOL. Motors do not disarm even after a crash I have to use Radio. flight mode does not beep when engaged. Motors seem under...
View ArticleFocus control on Sony cameras
@Hoehenarbeit wrote: Hi, I am using a Sony camera for aerial mapping and the camera takes two inputs to trigger: focus and shutter release. The common practice according to Camera Trigger Setup for...
View ArticleArducam OSD options - no rangefinder option?
@pilotltd wrote: I’ve got a Benwake TFmini-s installed which works well but there are a couple of issues with the data display. On the mission planner HUD screen the information overlays another...
View ArticleClik here to view.
Clipping of IMU3 Z Accelerometer
@copilot wrote: Hi A few days ago I pulled a log to check the vibrations on a newly build drone using a Cube Black. In general VIBE.VibeX, VIBE.VibeY and VIBE.VibeZ seems all good (well below 20)....
View ArticleClik here to view.
Heli DDFP Tail Rotor Setup
@nigel wrote: Hi All, Looking for some step by step help setting up a helicopter with DDFP tail rotor. Using a DJI Alpha 60A ESC and im not sure where the pwm ranges should be and just a good general...
View ArticleWhere in dataflash can I see throttle demand while in VTOL mode?
@Andre-K wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Compass Boot up Issues
@ardisd wrote: I have 2 copter both with Cube Black and Here GPS after upgrading to 4.03 I have noticed an issue with the Compass ID on both copters if I boot the pixhawk using USB Power...
View ArticleCompass calibration cylinder not sphere
@vig_nesh wrote: I’m using an apm 2.6 board with an internal compass.i tried to calibrate the compass but the shape after calibration looks like a cylinder and not a sphere.The problem is there are...
View ArticleExporting CAN information to external program
@Alex464 wrote: I’m fairly new to the pixhawk and mission planner itself so I apologize if this has already been asked and answered or if I’m simply missing the documentation. Currently I am trying to...
View ArticleRandom crazy altitude behavior in AltHold
@DroneUnit wrote: Hi All, 1600mm Flat Octo / 55lb Really struggling to figure out what is going on here. Ever 5 startups or so, the aircraft goes crazy in Altitude hold. It rapidly goes up and down...
View Article