Motor runs when disarmed
@mpjf01 wrote: I am using the current version of Arduplane on a Pixhawk. I upgraded the "Hawk from Arducopter. I habitually keep a handwritten log of the installation and setup steps as I take them...
View ArticleMounting Pixhawk and GPS
@TestAccount wrote: Hello, Why do Pixhawks and GPS modules not include mounting holes but instead only rely on tape, which needs to be replaced after a few uses? Is the tape supposed to aid in the...
View ArticleSolid yellow LED when trying to calibrate ESCs?
@DREW8110 wrote: I built a 600mm quadcopter with a Pixhawk flight controller. When trying to calibrate the ZTW Spider 30 amp Opto esc's, I get a solid yellow LED from the pixhawk. I put transmitter...
View ArticleDo-Digicam-Control does not work after landing
@Rocket wrote: I need help please. I have a mission in which the quad lands at a waypoint, then needs to take a photo using "Do-Digicam-Control". The quad then takes off and does a RTL. Everything...
View ArticleClik here to view.
Quadplane improve Yaw performance
@aamadeuss wrote: Hey Guys,my second quadplane had its qloiter maiden today. standart pids.Everything worked as expected, but the "yaw" performance is not good.its sluggy and the plane is not "stiff"...
View ArticleClik here to view.
DEV call 12 Dec 2016 3pm PST = 13 Dec 2016 2300 UTC
@CraigElder wrote: Copter release updates Vision updates wiki discussion - discuss possibility of moving to a simpler solution for ArduPilot.org's top page Rover Release ArduSub Release 3.5 General...
View ArticleArduSub v3.4 stable release candidate 1
@rjehangir wrote: Today we're happy to announce the first stable release of ArduSub. Today we've posted a "release candidate" that we would like you all test for the next few weeks until we can...
View ArticleClik here to view.
Pixhawk conect mission planner via UDP
@baoyuncheng wrote: hello,guys:recently,i am trying to connect pixhawk to MP(1.3.30 & 1.3.41...) via UDP. i can get some parameters in MP interface,but can't the full parameters.it just hangs in...
View ArticleDoes anybody have a Firmware Backup for the 3DR Solo Link Board (PN #PH11A)
@piousgreek wrote: Does anybody have a firmware backup from their 8 gb SD card on the 3DR Solo Link Board (PN #PH11A) or is there way to restore the contents? Posts: 1 Participants: 1 Read full topic
View ArticleRFD900 connection issues
@nikker wrote: Hi, just converted my system from pixhawk to pixhawk 2. I tried connecting my airside rfd900+ to telem 1 and telem 2 and can not get it to work. The radios show they are connected, led...
View ArticleBattery failsafe triiger on Pixhawk 2 Power port 2
@e72x wrote: Is it possible to set in Mission Planner that the Battery Failsafe triggered via Power port-2 on Pixhawk-2? Thanks, Posts: 5 Participants: 2 Read full topic
View ArticleUsing global velocity in body frame
@jverbeke wrote: Hi, I want to use the lateral (vy) velocity of my drone in body reference frame for outdoor application.So basically flight speed left/right in m/s. I see that I can get global...
View ArticleWhich made the mini heli crash
@talos wrote: I am using 3.4 to flying a mini heli, when I switch from stabilize to poshold a little suddenly, it just flied to earth vertically. Could some tell me what may cause this problem?...
View ArticleAntenna Tracker with PT785-S Pan & Tilt System (3.8:1)
@Marc_Dornan wrote: Despite the very few examples of APM antenna trackers being used for FPV in the field I am going to make one with the Servo City PT785 (3.8:1). Has anyone else used this? I will...
View ArticleClik here to view.
Missing Menu Options Under Config/Tuning
@skyveyor wrote: Just upgrade to the latest version of Mission Planner and noticed Advanced Params, Full Parameter List and Full Parameter Tree options are no longer present in the menu on...
View ArticleClik here to view.
SBUS problem with Arduplane
@ultrafuge wrote: @TridgeHopefully the right place to mention this issue: My Setup: Futaba T14SG + R7008SB in mode B connected to Pixhawk 1Arducopter 3.3.3: works with 12 channel FASSTest and works...
View ArticleClik here to view.
NOVAerial Robotics AC3.4-Heli Review and Issues List
@Rob_Lefebvre wrote: I wanted to open a new topic to announce that I am beginning to work with AC3.4 for TradHeli finally. I am reviewing the code, and will be posting my findings and updates here. As...
View ArticleClik here to view.
Desired Altitude adjustments observed in data logs
@jfield wrote: Hi guys, 3DR pixhawk running 3.4.3rc1 I've been seeing something in our logs that's more obvious as we push the flight times up. We put the multirotor in guided and send it to a...
View ArticleClik here to view.
Reset of integral part of PIDs with mode change
@EShamaev wrote: Hello all, When reviewing logs after last few flights, I noticed that the integral parts of PIDs are reset to zero when mode of flight changes.Is this done on purpose and if so, then...
View ArticleQuadplane : cannot hold position at final landing
@ravenfire wrote: cannot hold position at final landing，when reaching final land alt，the vehicle just drifted away. Posts: 1 Participants: 1 Read full topic
View Article