Clik here to view.
Offline map in mission planner
@Julien_768 wrote: Hi, does anyone know how to use offline maps in Mission Planner? thanks Posts: 3 Participants: 2 Read full topic
View ArticleOffsets for GPS and IMU
@ultrafuge wrote: @mackay9 Hi Randy, On DJI systems like A2 or A3 you have to set X,Y,Z relative to the CoG for the GPS and the IMU. Shouldn't we have this as well ? Posts: 2 Participants: 2 Read full...
View ArticleUsing Joystick instead of RC
@J.Leite wrote: Hi,I am trying to use a Joystick instead of a RC, we could configure the Joystick but every time we start the boat the Joystick configuration is lost and I have to setup it again....
View ArticlePixhawk - RSSI vs TBS Crossfire
@renatux wrote: Hello ! Anyone can get the RSSI value to show in mission planner/Tower from TBS Crossfire RX ? The telemetry link is OK, but the RSSI Value being impossible to me. Thanks Posts: 1...
View ArticleSITL, first project, fast plane
@stundenblume wrote: Hello,I would like to try my first steps in SITL. I managed to compile and fly the test plane some rounds.Now I would like to use a different airplane and simulate a fast jet,...
View ArticleUnknown error tones, burned pixhawk for no reason
@ITman496 wrote: I am diagnosing a friend's drone. It appears very dead, but we are trying to identify why. They said they had powered it up at one point to just check that everything was working. It...
View ArticleClik here to view.
Mission Planner display issues
@Pixel wrote: Hello allI have been having some issues with the latest version of mission planner 1.3.41 not displaying on the screen correctly.This only occurs once I have connected my UAV to the...
View ArticleConnections to Pixhawk Cube
@humanautopilot wrote: I'm completely new to autonomous vehicles (but I have a garage full of R/C helicopters, one of which will soon fly with my brand new Pixhawk Cube in it, so I know at least a...
View ArticleSpray drone tank empty alert arducopter
@Sivashankaruav wrote: The pesticides storage tank in spraying drone need indignation on low tank volume. I have digital water sensor which is been places to the bottom of the tank, It will change the...
View ArticleClik here to view.
Heading function to replace compass
@Sivashankaruav wrote: Hi all, Resent days RTK becoming Very popular and I came across some function called Heading to True North.The RTK module is enabled with two antenna facing in the same...
View ArticleSik hm-trp 500mw radio (915mhz)
@james_pattison wrote: I have one of these:http://www.aliexpress.com/item/32657321724/32657321724.html I haven't opened it up, but assume there is a PA to bump the rf output from 100 to 500mw.And it...
View ArticleHow To: Install APM Planner 2.0 On Raspberry Pi 2/3
@eclipse wrote: Installing APM Planner on a Raspberry Pi 2 or 3. This is a simple process if you know what you’re doing. The trick is trying to get up to date with all the forum posts and notes that...
View ArticleClik here to view.
Tilt Rotor TriPlane
@ChrisOlson wrote: I'm posting this blog post as a branch from this thread:http://discuss.ardupilot.org/t/tiltrotor-support-for-plane/8805 That thread deals with tilt rotor support in Plane. A couple...
View ArticlePixhawk not responding to Servo's
@Pranay_Jhunjhunwala wrote: Hello,I'm facing a problem with the response of servos from pixhawk.I am using a pixhawk with arduplane 3.5.2 firmware loaded.I connected the BEC to aux5/6 and a servo to...
View ArticleArdurower don't run both engines
@TomaszKn wrote: First you must see this my movie:MovieIn manual mode everything works ok.In autonomous mode is problem with engines.Boat floats along the right lines, but never run both engines.On...
View ArticleUART Disabled output in certain functions
@havi0019 wrote: Hello, I am have been using hal.uartD with a ftdi to send data to external computer for year or two. I did all my uart calls in userCode which has worked with success over different...
View ArticlePixhawk fails to log any data
@havi0019 wrote: Hello I have been using this pixhawk for maybe a month. I modified Copter 3.3 rc5 code a bit - nothing too drastic. One thing I did do is I modified one of the log messages(log_Rate)....
View ArticleClone boards and settings in MP
@Adam_Campbell wrote: Got my board 2.8 from amazon 80.00 with compass,power module and 433mhz set. When loading 3 questions Linux? Been saying yesThen is this 2+ ? Been saying yesIn the configuration...
View ArticleAdd waypoints to APM Planner with python or http GET
@eclipse wrote: I've been digging for days researching this, and on diydrones I found this quote but have not been able to find any more details on it: apm planner support a very simple guided mode...
View ArticleMotor makes one beep noise when powered on with one esc
@npatel023 wrote: Hi, I am using 30amp simonk escs with 920kv motors. When I power the esc on with my 3s battery, the motor makes one beep noise when it should be making 3. I have tried different...
View Article