External LEDs & Buzzer
@Sergey wrote: I know, that starting somewhere from AP 2.73 this stuff is not supported and can not be activated through MissionPlanner. But I read here...
View ArticleWhat are these errors, GPS-2 and Failsafe GPS-1
@virgodave61 wrote: I'm getting these errors, how do you look up errors like this so I don't have to ask on the forum? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Telemetry data transfer very slow
@ahmed wrote: Hi all , In my plane I am using 9Xtend module 1watt 900MHz for telemetry . The 9Xtend accept 2 baudrate for RF (9600 - 115200 ) . when I use 9600 and connect with mission planner , Get...
View ArticleClik here to view.
Pixhawk Telemetry Setup
@newmafi wrote: Hello, gentlemen.I'm learning step by step about Pixhawk.Thanks to valuable advice and posts here, I can manage to solve many problems and succeed in setting up a very stable and crisp...
View ArticleCopter-3.4 beta testing start
@rmackay9 wrote: Copter-3.4-rc1 should appear in the mission planner's "Beta firmware" link within a couple of hours of this post. All feedback welcome. Changes from 3.3.31) EKF2 allows "boat mode"...
View ArticleCompass variance known problem?
@wjaxxx wrote: We have been using 3.3 in our copters for a while now and we see a lot of issues with compass variance. We are quite sure there some be something in the code that is triggering these...
View ArticleClik here to view.
How long Autotune?
@Don_Sebastian wrote: I built myself medium-sized Copter Quad X. 15,5" propeller, 10000mA Lipoflying quite well so far, but I'm not finished with Autotune. In videos and tutorials is always said /...
View ArticleBeginners guide to error messages and beep tones
@3rdzeropoint wrote: Please ensure your version is AC3.3+ for complete beginners there is a lack of info on getting started and this type of error message that stumps Posts: 2 Participants: 2 Read...
View ArticleDoes AC3.4 work with Mission Planner?
@cagiva851 wrote: Can we use MissionPlanner-1.3.38 with Copter-3.4 or should we use a different version of MP? Same question for APM Planner, can APM Planner 2.0.21 be used to configure the vehicle...
View ArticleThrow Mode Throttle
@dkemxr wrote: Does the throttle position have to be off of zero before tossing the craft in Throw Mode? I suppose you will want it at mid throttle before switching modes after it's flying anyway but...
View ArticleUsage of Storm32 Gimbal with Pixhawk via mavlink
@Francis wrote: Hi, i am using a Storm32 gimbal with my copter 3.3.2 on a pixhawk as described in http://ardupilot.org/copter/docs/common-storm32-gimbal.html My questions are: can i remote trigger my...
View ArticleThe Best & Easy simulation method for plane ..!
@ahmed wrote: Hi all , Before two months I try to work with simulation for my plane but always I found problems , I try flight gear , Xplane 10 , but they didn't work well for me , Now I want to try...
View ArticleRC Transmitter Flight Mode Configuration for DX8G2
@Clint_Harris wrote: Looking for help setting up Spektrum DX8G2 with 6 flight modes. Tried using the instructions does DX8 but it does not work. Can someone please spare a few minutes to help a fellow...
View ArticleAC3.4-rc1 Testing Today
@JoeBreznai wrote: Loaded the 3.4rc-1 today on my MQ600 Quad with a Pixhawk on board, and got 5 flights with no issues. I did no calibrations or other setup from previous 3.3.3 software for the first...
View ArticleRTL stalls on climb
@povlhp wrote: Hi, Have the APM 2.6 in a bix3. On RTL it flies fast and more steep up than possible in FBWA. Yesterday it caused 2 stalls just after each other. What parameters controls RTL flight?...
View ArticlePixRacer: Relay Pin for Camera Trigger [solved]
@Thorsten wrote: Hi all, I am trying to setup a camera relay trigger with PixRacer.CH7 is working, BRD_PWM_COUNT = 4, CAM_TRIGG_TYPE = 1 I tried all numbers listed in Mission Planner but without...
View ArticleClik here to view.
Antenna RF Test box, build log. Part 1
@jpkh wrote: RF Testing in generally is a black magic... As you know. RF Testing is usually very expensive, rather challenging and a lot of VODOO around it. Why?? Well because it just is. You are...
View ArticleOne shot 125 config
@cala2 wrote: To use oneshot 125 I have to enable by mot pwm type=2 and someelse to config? Posts: 4 Participants: 2 Read full topic
View ArticleRead a float number from serial port
@Tearabbit317 wrote: hello all, new to forum, hoping I can find the answer of how to read a float number from the serial port. I am implementing a pid controller to my drone, using the HAL library and...
View ArticleError Flight mode 5 Loiter
@Inabnit wrote: Good Evening, I come here since I ran out of Ideas and hope that somebody can look at one of my logs. My quad flew fine a few days before (Loiter,Auto,RTL worked well) however i had...
View Article