Clik here to view.
Pixhawk Lite - AltHold issue on WOT
@Piet wrote: Hi,I built in a PHL V2 in my quad now...All works pretty fine, BUT when flying very fast in AltHold or PosHold the aircraft looses high!Slowly but constant.... Barometer got no errors and...
View ArticleControl, Navigation, and Obstacle Avoidance Simulation
@wilselby wrote: Hello everyone, I have put together some fairly comprehensive tutorials and videos covering control system design, simulation, and implementation through 3d mapping, path planning,...
View ArticleDangerous altitude climb
@jaredm wrote: I was flying my copter in loiter mode in pretty strong wind. Every once in a while the altitude would shoot up. My copter would take off like a rocket. The logs show that it knows its...
View ArticleAdd new camera in tower 3.2.1
@Ignacio_Ramirez_Sepu wrote: how to add new camera in the version 3.2.1 Posts: 1 Participants: 1 Read full topic
View ArticleCurrent preferred sources of APM 2.6/2.8 hardware?
@TangoEchoAlpha wrote: These days, where can I buy well made APM boards? Posts: 1 Participants: 1 Read full topic
View ArticleSetting up a Walkera QR X350 Pro with Fly Sky X9 (Turnigy 9X) Transmitter
@bapservice wrote: After setting up my new transmitter i have the following problems 1/ Range is limited to approximately 100 Metres. Loses signal Returns to Launch (RTL) and lands (no drift)2/ On GPS...
View ArticleNeed help with AUX Outputs for Servo Control
@Paul-H wrote: Hi all I need some help getting servos connected to the AUX ports on my Pixhawk working I am running AP3.3 I am using a 10 Channel receiver running in PPM PPM out is connected to RCIN...
View ArticleMotor speed- ArduPilot 2.5 Hexa V3.2.1
@vasco wrote: I have Ardupilot 2.5 with hex firmware. How can I change parameter for the motor round. The drone do not takeoff and I think it doesn't take the appropriate power to take off!! I am...
View ArticleSetting up the TX1
@rmackay9 wrote: I've got a J120 board from Jurgen at Auvidea.ea and a TX1 board. The J120 board seems to work pretty much as advertised. It's small enough to fit on a medium sized quadcopter (won't...
View ArticleCreating a new flight mode for ArduPlane
@Swetapadma wrote: Hi! I was wondering about how I could integrate a new flight mode for ArduPlane. Any help would be appreciated.The documentation is available for Copter, but I am confused about how...
View ArticleClik here to view.
Arducopter safety auto land initialisation?
@ACPUK wrote: Hi all, I have been looking at a rig that has landed several times un-expectedly.Upon looking into the log I see there is a problem with the hardware. One or two of the motors off set...
View ArticleClik here to view.
New guy here trying to make sense of it all
@Rick_Blacker wrote: Hi all, I'm new to the world of drones. I've been developing software for about 18 years now. I've been scanning various sites like Ardupilot, dronecode, diydrones. I've noticed...
View ArticleDouble precision for waypoints in Auto mode. Is it possible?
@Johny wrote: Hi everyone,Is it possible to make pixhawk 1/2 support double precision for waypoint coordinates? Can we make use of uint32 for lat/lon instead of float? Regards,Johny Posts: 2...
View ArticleAltHold Algorithm Bug
@buckker wrote: Hello FriendsI posted my problems in connection with overshooting in the AltHold mode a few months ago on DIYDrones. But nobody really listen... Today I did some aerial footage for a...
View ArticleRc1_trim value changes after every operation in skid_steering mode
@gray03 wrote: Hi,I want to drive my rover on a straight line in manual mode with skid_steering. I am using an apm 2.6, turnigy 9xr and 2 brushed dc motors.In mission...
View ArticleGuided mode altitude
@Hein_Du_Plessis wrote: I've just tested guide mode on Tower for the first time and I found that, at least in plane, the altitude entered seems to be meters above SEA LEVEL in stead of HOME. Besides...
View Article3DR Iris + Crashed after 3 successful waypoints mission
@ankitsarvaiya1 wrote: Hi all, Could someone point out what went wrong with my flight today? I've had three successful flight before this and during my last flight, quad copter went into a crazy side...
View ArticleLoiter_To_ALT missing in 1.3.38?
@ahmed wrote: I just check mission planner I didn't found the comman LOITER_TO_ALT in the commend list . Dose that happen to every one ? It was very good command and useful . . Posts: 2 Participants:...
View ArticleStructure of the code
@Swetapadma wrote: Hi, I am new to all of this, and am trying to make sense of the code. What I can't understand is, what is the main code that runs? All the cpp files have function declarations only....
View ArticleClik here to view.
Bad/Corrupt Dataflash logs, 60mb of non-stop "ÿÿÿÿÿÿÿÿÿÿÿ"
@npatzke wrote: So about half of my logs come out 'corrupted' for a lack of a better word... The size of logs usually seem appropriate for the length of flight, but when opened they're a non-stop...
View Article