How to obtain Mission Planner multi-layer directory Structure illustration?
@gaojizhong wrote: Hello, eveybody!I am a new guy on Mission Planner compile, I want to understand the MP's directory structure illustration I want to edit the strcuture files to change the display's...
View ArticleClik here to view.
Navio2: erratic PWM output
@Alexey wrote: Have a problem with output pwm on Navio2, then disarmed.On version ArduCopter-quad 3.4.4 all is good: Screenshot from 2017-02-07 12-29-12.png1051x229 21.6 KB On version 3.5rc-1 after...
View ArticleMavproxy -streamrate parameter
@bendead wrote: Hi Guys I am trying to play a bit with mavproxy, the goal is to send telemetry at a rate of once every 30 seconds. The lowest speed I can achieve with the -streamrate parameter is once...
View ArticleTelemetry with dronekit
@tipehugo wrote: Hi, I would like to do real tests with a lightweight plane with drone-kit from the ground. It means that I need to send orders and retrieve sensed data from my plane. For that I will...
View ArticleAutotune as a flight mode
@bpoxman wrote: About the Autotune , we can read in the online documentation ( Advanced Configuration » Tuning » AutoTune ->Additional Notes : In Copter-3.3 (and higher) AutoTune can be setup as a...
View ArticleIn MP getting massage CKECK BRD_TPYE NO l3g20 found
@mfbs17 wrote: What doe it mean?how to correct it? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Autotune only tuning "ROLL"
@flyinghigh wrote: Hi. I'm running ArduCopter V3.2.1 (36b405fb). When I perform "autotune" it is only tuning the "roll" axis. I have searched in the beta MP 1.3.44.2 for the parameter "AUTOTUNE_AXES"...
View ArticleHow to power the PWM to PPM converter It works plugged in to my computer
@wacked wrote: It works plugged in to my computer via plainer. i can unplug it and it still works, will arm dis arm. I unplug the battery and plug it back in it will not arm until plugged back in to...
View ArticleI know I ask a lot of questions. Please tell me if you used this
@wacked wrote: I received A PX4 today that came with a PPM encoder, Does it work? Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Non-zero Desired Roll on takeoff
@frizensami wrote: Hey all, During a recent test with Pixhawk 2, Arducopter 3.4.4 and a 500-size heli frame, I noticed that the copter tended to roll right quite significantly during takeoff, so the...
View ArticleSingle copter CG and CMposition
@Tufan_Samal wrote: I am trying to build a single rotor copter with 4 control vanes . but i am confused about the position of its center of mass and center of gravity . as in case of quadcopters i...
View ArticleHard (or impossible) compass calibration on 2.8
@jackflash2000 wrote: Hi everybody!(From Italy)I have a problem with the calibration of the compass. At the firs installation, everything was gone ok, but after the reset (for other reasons that I'm...
View ArticleGuided_noGPS + Ras Pi not working
@muqing_cao wrote: Hi everyone, Recently I am working on a project to control Pixhawk with Rasp berry Pi running ROS and MavRos. I am sure that the communication between the Ras Pi and Pixhawk is set...
View ArticleFailsafe problem with frsky taranis plus on pixhawk
@aidil wrote: Hi everyone...I have taranis plus with x8r rx..The problem is i cannot set the lowest throttle value below than -100 (min) for taranis tx..Then when i set the failsafe for pixhawk, the...
View ArticleClik here to view.
Updating wiki for uploading firmware on PixHawk
@adnan_ul_haque wrote: 08-Feb-2017 Hello: I just started with PixHawk. Uploaded the firmware successfully AC3.4.4 via MP1.3.44.2, following wiki...
View ArticleFlow Sensor Calibration Mistake?
@matthewmax09 wrote: Hello, I am trying to get my quad to loiter using a Px4Flow senor and a teraranger one rangefinder. Following the steps for installing both sensors onto the frame, the quad is...
View ArticlePIxhawk 2 IMU3 damped?
@Charlie_R wrote: Can't seem to find this info anywhere - which of the IMU's are damped? Got the PH2.1 in the air yesterday and surprised to find less vibration from IMU3 than the first two - I was...
View ArticleCopter pauses/stops during Auto flight
@mapper905 wrote: I'm using a DJI S900 copter with Pixhawk. I've noticed the copter "pausing", or at least wide swings in speed from the planned speed. This seems coupled with the inability to hold...
View ArticleProblem to fix my APM 2.8 and GPS
@Kikirikiki90 wrote: Hi, I am mounting my Copter with an APM 2.8, Turnigy 9x and a GPS NEO 6M. I'm trying to set it up but I get 2 errors when I try to calibrate it. --> The first one is when I try...
View ArticleHobby king px4flow sensor not working on i2c?
@kalabaddon wrote: Hello all, I am making a 1200mm hex and I am having issues with the hk flow sensor. as of now the flow sensor works when I directly connect it to the usb (as if I was updating the...
View Article