ESP8266 WIFI on pixhawk
@gnkarn wrote: im still surprised that there is no dev to adapt the pixracer wifi module for the pixhawk . did any body found other way to make this connection to work by using other firmware on the...
View ArticleDJI f450 ESCs keep beeping after calibration and unable to arm
@klytech wrote: I am using DJI f450 ARF kit with included motors and ESCs, and 3DR Pixhawk MINI. The software I am using is ArduCopter 3.5-rc1 beta testing. I followed the directions here...
View ArticleHow much capacity of battery supported by apm2.6
@umarufx wrote: I am using apm2.6 quadcopter and having 3dr power module. My question is can i use 5200mah 40c 3s lipo battery Posts: 1 Participants: 1 Read full topic
View ArticleLocation of Other Basestations Displayed
@cndnflyr wrote: I'm using RFD900+ radios with 2.x firmware to control a copter from multiple base stations. The copter is Node 0 and transmits to all the other stations. Each station only transmits...
View ArticleAdvanced PID writing permission
@UFOdesigner wrote: Hello, when connecting the laptop to my octocopter (coaxial quadcopter design with Pixhawk) I am not able to rise the Advanced PID Tuning Parameters within the MissionPlanner GUI...
View ArticleMission planer menu missing
@ylgolan wrote: I am working with win 10in the menu I config/tuning I have on the left side only planerI can non find full parameterwhat is the reasen ? Posts: 1 Participants: 1 Read full topic
View ArticleESC calibration not possible, T-Motor S45A 600Hz on Pixhawck (3.4.4)
@bluemarlin wrote: Dear helpers I try to calibrate 4 ESCs Type: "T-Motor S45A 600Hz" with SimonKhttps://www.fpv24.com/de/t-motor/t-motor-s45a-esc-simonk-software-2-6s?c=2711 After pressing the safty...
View ArticleClik here to view.
Unexpected Land in AUTO MODE
@alexmainardi wrote: Hi, Last week I have some issues during AUTO Mission (FW 3.4.3), the copter stops at the middle of the mission and land (Apparently without change Flight Mode). Reading the...
View ArticleAC 3.3.2 Quad Destabilizing
@vkt62 wrote: Hi all,I am running AC 3.3.2 using Pixhawk 1 on my quad after having flown for several weeks, I suddenly started having stability problems randomly. When this happens, the system...
View ArticleServo Functions
@ardisd wrote: On the latest version of Mission Planner with Copter 3.5 could some give me a list of the functions for Servo5_functions Posts: 1 Participants: 1 Read full topic
View ArticleRover Data Streams
@IdlePhase wrote: Hi folks, I'm wondering where I could find documentation for which messages are in each data stream. I have found the definition in the streams in the MAVLink C library under...
View ArticleDEV call 06 Feb 2017 3pm PST = 06 Feb 2017 2300 UTC
@CraigElder wrote: Copter 3.5 release update object avoidance / vision project update - 1st draft of ROS install scripts for TX1 produced, point cloud produced using ZED camera. Plane firefly6 frame...
View ArticleClik here to view.
"Bad Compass Health"
@portsample wrote: I'm having a problem with a Pixhawk that came with a 3DR DIY 4X kit. APM Planner is reporting "Bad Compass Health". The compass is an external uBlox GPS combo that came with the...
View ArticleMultiple channels with elevon_ouput
@weliwarmer wrote: Hi, I have an FX-79 and would like to add the extra tabs as elevons without a splitter wire. The servos can be wired up to Main 5 & 6 with the RC5_FUNCTION & RC6_FUNCTION to...
View ArticleTake off command from MAVLink
@jasonbeach wrote: How do you send a command to takeoff directly from MAVLink (from a companion computer)? Right now via MAVLink I:-check GPS and EKF to make sure I can arm the vehicle-change mode to...
View ArticleClik here to view.
SB_0000001 Critical service bulletin for Beta Cube 2.1
@proficnc wrote: ** If you have a Pixhawk 2.1 Delivered in 2016, please follow these instructions before further flight. ** This does NOT affect the Alpha boards, it does not affect 2.0 boards (SOLO)...
View ArticleClik here to view.
Pixhawk output rail does not give any output
@aidil wrote: Hi all,i hve a problem with the signal for my output..i try to measure the ch1's voltage using multimeter where i assign my aileron but sadly no incoming signal going out(should be 5V...
View ArticleClik here to view.
Anyone use Blue Robotics Fathom X/Raspberry PI Tethered on a Crawler?
@gsprince16 wrote: I recently purchased a small round tire inspection bot from Superdroidrobots, and it came with a Saber tooth motor controller which worked well. I installed my Spektrum RC/TX and it...
View ArticleMotors chatter while disarmed
@flyingw wrote: After arming and throttling up, they run smoothly. I tried increasing the deadband without result. What can be causing this? Thanks, Paul Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
RC Mapping error?
@klytech wrote: I am using Spektrum DX6e Transmitter with AR610 receiver, and using an Usmile PPM encoder (https://www.amazon.com/gp/product/B019V59KCS/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1)...
View Article